-
What are the different areas of the office?
Front Office, Reception, Operatories, Sterilization, Utility Room, X-ray, Supply Room, Consultation Room, Lab, Technology, Handpieces and Small Equipment.
-
What temp should the reception area be?
72 F
-
What temp should it be in the clinical areas?
68 F to 70 F.
-
Upright position...-
the back of the chair is positioned at a 90 degree angle.
-
Supine position-
Patient is positioned as if lying down.
-
Subsupine Position-
Patient's head is lower than their feet.
-
Front delivery-
Dental unit is positioned over the patient's chest.
-
Side delivery-
Either side of the patient's chair.
-
Rear delivery-
Positioned behind the dental chair near the back of the patient's head.
-
Rheostat-
Operates and controls the speed of the handpieces.
-
How does the air-water syringe function?
Delivers a steam of water, delivers a steam of air, deliverys a combined spray of air and water.
-
What should you do in the morning routine?
Turn on all equipment. x-ray machine, sterilizer, evacuator.
-
Saliva Ejector-
is used for less-invasive procedures, like routine cleanings, placement of sealants, and fluoride application.
-
High-volume evacuator-
most assistants will used this because it has a larger head and can clean saliva a lot faster.
-
Curing light-
used to harden or cure light sensitive dental materials.
-
Amalgamator-
electrical machine used to mix materials by shaking the capsule that holds the ingrediants.
-
Central Vacuum Compressor-
provides the suction for oral evauation systems. Consists of two parts, compresor and vacuum tank.
-
Compressor-
creates the flow of air in the central vacuum compressor.
-
Vacuum tank-
screens the flow of air to create suction.
-
How far should the assistant be above the dentist?
4 to 6 inches.
-
Classif. of Movements: Class I:
Move ment of fingers only.
-
Classfi. of Movement: Class II:
Movement of fingers and wrist.
-
Classfi. of Movements: Class III:
Movement of fingers, wrist, and elbow.
-
Classfi. of Movements: Class IV:
Use of the entire arm and shoulder.
-
Classfi. of Movements: Class V:
Use of the entire torso.
-
What does the number mean on an instrument?
Width, Length, Angle.
-
Hand instruments are designed with three parts:
handle, shank, working end.
-
Instruments are designed to have a_____
larger handle in circumference as well as padding for a better grip.
-
Shank-
the thickness of the shank dictates the amount of pressure can be applied to the intrument without breakage.
-
The instruments used in restorative procedures are classified into four categories:
examination, hand cutting, restorative, and acessory.
-
Examination instruments-
allows the operator to examine the health status of the oral cavity. (mouth mirror, exployers, cotton pliers, periodontal probe)
-
hand cutting instruments-
allows the operator to remove decay manually and to smooth, finish, and prepare the tooth structure for its final restoration. (Evacuator, hoe, chisel, hatchet, gingival margin trimmer)
-
Restorative instruments-
allows the operator to restore a tooth by placing, condensing and carving a dental material to the anatomy of the tooth.
-
Accessory instruments-
are miscellaneous instruments and items that are used in the procedure. (Scissors, spatulas, amalgam well, howe pliers, articulating paper holder.)
-
Mouth mirror-
indirect vision, light reflection, retraction and tissue protection.
-
Amalgam instruments-
Amalgam carrier, condenser, burnisher, carver, Hollenback carver.
-
Composite instruments-
composite placement, The Woodson.
-
preset trays-
exam, amalgam, composite, crown&bridge, endodontic, surgical.
-
Instrument sequence-
left to right. Basic, additional examination instruments, hand cutting, restorative, and accessory.
|
|