Recip Inspections Test 3

Card Set Information

Author:
Anonymous
ID:
227988
Filename:
Recip Inspections Test 3
Updated:
2013-07-23 22:49:13
Tags:
Roberts recip reciprocating engine inspections
Folders:

Description:
Engine Inspections Test Notes
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user Anonymous on FreezingBlue Flashcards. What would you like to do?


  1. Determine which portion of the AD is applicable for Model O-690 series engine, serial No. 5863-40 with 283 hours' time in service.
    This is the compliance portion of an FAA Airworthiness Directive.Compliance required as indicated:
    (A) For model O-690 series engines, serial Nos. 101-40 through 5264-40 and IO-690 series engines, serial Nos. 101-48 through 423-48, compliance with (C) required within 25 hours' time in service after the effective date of this AD and every 100 hours' time in service thereafter.
    (B) For Model O-690 series engines, serial Nos. 5265-40 through 6129-40 and IO-690 series engines, serial Nos. 424-48 through 551-48, compliance with (C) required as follows:
    (1) Within 25 hours' time in service after the effective date of this AD and every 100 hours' time in service thereafter for engines with more than 275 hours' time in service on the effective date of this AD.
    (2) Prior to the accumulation of 300 hours total time in service and every 100 hours' time in service thereafter for engines with 275 hours or less time in service on the effective date of this AD.




    (C) Inspect the oil pump drive shaft (P/N 67512) on applicable engines in accordance with instructions contained in Connin Service Bulletin No. 295. Any shafts which are found to be damaged shall be replaced before further flight. These inspections shall be continued until Connin P/N 67512 (redesigned) or P/N 74641 oil pump drive shaft is installed at which time the inspections may be discontinued.
    (B), (1)
  2. A Cessna 180 aircraft has a McCauley propeller Model No. 2A34C50/90A. The propeller is severely damaged in a ground accident, and this model propeller is not available for replacement. Which of the following should be used to find an approved alternate replacement?
    Aircraft Specifications/ Type Certificate Data Sheets.
  3. On a reciprocating engine aircraft using a shrouded exhaust muffler system as a source for cabin heat, the exhaust system should be
    Visually inspected for any indication of cracks or an operational carbon monoxide detection test should be done.
  4. (1) Airworthiness Directives are Federal Aviation Regulations and must be complied with unless specific exemption is granted.
    (2) Airworthiness Directives of an emergency nature may require immediate compliance upon receipt.Regarding the above statements,
    Both No.1 and No.2 are true.
  5. Which of the following contains a minimum checklist for 100-hour inspections of engines?
    14 CFR Part 43 Appendix D
  6. When must an Airworthiness Directive (AD) be complied with after it becomes effective?
    As specific in the AD.
  7. Which of the following contains a table that lists the engines to which a given propeller is adaptable?
    Propeller Type Certificate Data Sheet
  8. Which of the following component inspections is to be accomplished on a 100-hour inspection?
    Check cylinder compression
  9. You are performing a 100-hour inspection on an R985-22 aircraft engine. What does the '985' indicate?
    The total piston displacement of the engine.
  10. Where would one find type design information for an R1830-92 engine certificated under the Civil Air Regulations (CAR) and installed on a DC-3?
    The aircraft engine specifications.
  11. Straightening nitrided crankshafts is
    Not recommended
  12. The breaking loose of small pieces of metal from coated surfaces, usually caused by defective plating or excessive loads, is called
    Flaking
  13. Each powerplant installed on an airplane with a Standard Airworthiness Certificate must have been
    Type Certificated
  14. A severe condition of chafing or fretting in which a transfer of metal from one part to another occurs is called
    Galling
  15. Indentations on bearing races caused by high static loads are known as
    Brinelling
  16. When inspecting an aircraft reciprocating engine what document is used to determine if the proper magnetos are installed?
    Aircraft Engine Specifications or Type Certificate Data Sheets
  17. Which of the following can inspect and approve an engine major repair for return to service?
    Certificated Mechanic with Inspection Authorization.
  18. What publication is used for guidance to determine whether a powerplant repair is major or minor?
    Federal Aviation Regulations, Part 43, Appendix A
  19. The airworthiness standards for the issue of type certificates for small airplanes with nine or less passenger seats in the normal, utility, and acrobatic categories may be found in the
    Federal Aviation Regulation, Part 23
  20. Which of the following contains approved data for performing a major repair to an aircraft engine?
    Manufacturer's maintenance instruction when FAA approved.
  21. What maintenance record(s) is/are required following a major repair of an aircraft engine?
    Entries in the engine maintenance record and FAA Form 337
  22. A ground incident that results in propeller sudden stoppage would require a crankshaft runout inspection. What publication would be used to obtain crankshaft runout tolerance?
    Current Manufacturer's maintenance instructions.
  23. Select the Airworthiness Directive applicability statement which applies to an IVO-355 engine, serial number T8164, with 2,100 hours' total time and 300 hours since rebuilding.
    Applies to all IVO-355 engines, and serial numbers T8000 through T8300, having less than 2,400 hours' total time.
  24. How are discharge nozzles in a fuel injected reciprocating engine identified to indicate the flow range?
    By an identification letter stamped on one of the hexes of the nozzle body.
  25. What section in the instructions for continued airworthiness is FAA approved?
    Airworthiness Limitations section.

What would you like to do?

Home > Flashcards > Print Preview