NAVEDTRA 14040 BLUEPRINTS

Card Set Information

Author:
fishphinfan
ID:
229828
Filename:
NAVEDTRA 14040 BLUEPRINTS
Updated:
2013-08-12 21:34:25
Tags:
BLUE PRINTS
Folders:

Description:
BLUE PRINT MANUAL CH'S 1, 2, 3
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user fishphinfan on FreezingBlue Flashcards. What would you like to do?


  1. WHAT BLUE PRINT PUBLICATION SPECIFIES THE SIZE, FORMAT, LOCATION, AND TYPE OF INFORMATION THAT SHOULD BE INCLUDED IN MILITARY BLUE PRINTS.
    MIL-STD-100A
  2. WHERE IS THE TITLE BLOCK LOCATED ON A MILITARY BLUE PRINT?
    LOWER RIGHT CORNER
  3. WHAT INFORMATION IS FOUND IN THE TITLE BLOCK ON BLUE PRINTS?
    • DRAWING NUMBER
    • NAME OF PART
    • PART IDENTITY INFORMATION
    • NAME AND ADDRESS OF GOV. AGENCY
    • SCALE
    • DRAFTING RECORD
    • AUTHENTICATION
    • DATE
  4. WHERE WOULD THE REVISION BLOCK BE IF A BLUE PRINT HAD A REVISION TO IT?
    UPPER RIGHT HAND CORNER
  5. HOW IS A REVISED DRAWING IDENTIFIED?
    BY THE ADDITION OF A LETTER AFTER THE DRAWING NUMBER. (REV. A) OR (REV. B)
  6. WHAT IS THE PURPOSE OF ZONE NUMBERS ON BLUE PRINTS?
    TO HELP IDENTIFY A PART IN THE DRAWING. ie USE THE ZONE NUMBERS LIKE LATITUDE AND LONGITUDE ON A MAP
  7. WHAT IS THE BILL OF MATERIAL BLOCK IN BLUE PRINTS?
    IT IDENTIFIES ALL PARTS ON THE BLUE PRINT BY PART NUMBER AND QUANTITY (IPB)
  8. WHAT ARE FINISHING MARKS ON A BLUE PRINT?
    THEY IDENTIFY PARTS THAT REQUIRE MACHINE FINISHING.
  9. WHERE IS THE LEGEND FOUND ON A BLUE PRINT?
    UPPER RIGHT CORNER
  10. WHAT ARE PRELIMINARY PLANS?
    SUBMITTED WITH BIDS BEFORE A CONTRACT IS AWARDED
  11. WHAT ARE CONTRACT PLANS?
    ILLUSTRATE MANDATORY DESIGN FEATURE OF THE SHIP
  12. WHAT ARE CONTRACT GUIDANCE PLANS?
    ILLUSTRATE DESIGN FEATURES THAT ARE SUBJECT TO DEVELOPMENT
  13. WHAT ARE STANDARD PLANS?
    SHOW ARRANGEMENT, OR DETAILS OF EQUIPMENT, SYSTEMS OR PARTS, WHERE SPECIFIC REQUIREMENTS ARE NECESSARY
  14. WHAT ARE TYPE PLANS?
    SHOW GENERAL ARRANGEMENT OF EQUIPMENT, SYSTEMS OR PARTS THAT DO NOT REQUIRE STRICT COMPLIANCE TO DETAILS
  15. WHAT ARE WORKING PLANS?
    THEY ARE WHAT THE WORKERS USE TO BUILD
  16. WHAT ARE CORRECTED PLANS?
    PLANS THAT HAVE BEEN CORRECTED TO SHOW FINAL SHIP ARRANGEMENT, FABRICATION, AND INSTALLATION
  17. HOW MANY PARTS IS THE BLUE PRINT NUMBERING PLAN?
    FIVE
  18. WHAT ARE THE FIVE PARTS OF THE BLUE PRINT NUMBERING PLAN?
    • SIZE
    • FEDERAL SUPPLY CODE
    • TWO PART SYSTEM COMMAND NUMBER
    • REVISION LETTER
  19. WHAT IS A PROTRACTOR USED FOR?
    TO MEASURE OR LAY OUT ANGLES
  20. WHAT IS THE FRENCH CURVE USED FOR?
    TO DRAW IRREGULAR CURVES WITH UNLIKE CIRCULAR AREAS WHERE THE CURVATURE IS NOT CONSISTENT
  21. WHAT ARE HIDDEN LINES IN SKETCHING?
    SHORT, EVENLY SPACED DASHES TO SHOW HIDDEN FEATURES OF AN OBJECT
  22. WHAT ARE CENTER LINES IN SKETCHING?
    ALTERNATING LONG AND SHORT DASHES, USE THEM TO IDENTIFY THE AXIS OF SYMMETRICAL PARTS
  23. WHAT ARE BREAK LINES IN SKETCHING?
    SHORTEN THE VIEW OF LONG UNIFORM, OR WHEN YOU ONLY NEED A PARTIAL VIEW. LONG BREAKS USE THIN LINE WITH FREE HAND ZIGZAG, SHORT BREAKS USE THICK DRAWN LINE WITH FREE HAND ZIGZAG
  24. WHAT ARE PHANTOM LINES?
    LONG DASHES, SEPERATED BY PAIRS OF SHORT DASHES. THESE LINES SHOW ALTERNATE POSITION OF PARTS.
  25. WHAT ARE STITCH LINES?
    SHOW SEWING OR STITCHING IN A DRAWING. USE SHORT THIN DASHES SPACED .016 OR DOTS SPACED .12 INCH APART.
  26. WHAT ARE CHAIN LINES?
    CONSIST OF THICK LONG AND SHORT DASHES. THIS SHOWS THAT AREA IS TO RECEIVE ADDITIONAL TREATMENT OR CONSIDERATIONS
  27. WHAT IS ISOMETRIC PROJECTION?
    SHOWS THE OBJECTS ALL THREE SIDES

What would you like to do?

Home > Flashcards > Print Preview