BRCD BCFA.txt

Card Set Information

Author:
kryptofuzz1
ID:
249010
Filename:
BRCD BCFA.txt
Updated:
2013-11-25 13:59:14
Tags:
Brocade
Folders:

Description:
Brocade
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user kryptofuzz1 on FreezingBlue Flashcards. What would you like to do?


  1. You have a server with a Fibre Channel address of 0x241932 that is causing problems.

    To which physical port on the switch is the server connected?

    A. 19
    B. 25
    C. 32
    D. 24
    B. 25
    (this multiple choice question has been scrambled)
  2. You have been asked to analyze a Fibre Channel address.
    Which three sections make up the address? (Choose three.)

    A. area ID
    B. fabric controller ID
    C. node address
    D. name server ID
    E. Domain ID
    ACE
  3. You have a Fibre Channel address of 0x240932 and need to determine to which switch it belongs.
    What is the decimal value of the Domain ID of the switch?
    A. 09 
    B. 24
    C. 32
    D. 36 
    D
  4. You will be installing 48-port blades into your Brocade DCX Backbone and therefore shared area
    addressing will be used.

    Which two fields are used to distinguish this value? (Choose two.)

    A. Domain ID
    B. area ID
    C. WWN
    D. node address 
    BD
  5. You have been asked by your co-worker to configure the Domain ID on a new Brocade 6510
    switch. The Domain ID is 0xEF.

    What is the decimal value you would use to configure your switch with this domain?

    A. 1
    B. 101
    C. 239
    D. 255 
    C
  6. In the exhibit, on which physical port is the end device attached?

    A. 00
    B. 01
    C. 09
    D. 10 
    C
  7. You have an ISL between two switches.

    When verifying the connection using the switchshow command, which port type should be shown
    for the ISL?

    A. E_Port
    B. F_Port
    C. G_Port
    D. N_Port 
    A
  8. Which two switch port types are expected upon successful completion of port initialization?
    (Choose two.)

    A. G_Port
    B. F_Port
    C. E_Port
    D. U_Port 
    BC
  9. In which two situations would you use a D_Port? (Choose two.)

    A. testing data traveling over an ICL connection
    B. testing connectivity to a host
    C. testing loopback ports
    D. testing long distance cables and SFPs 
    CD
  10. Which type of port will be initialized on a storage device upon attachment to a switch with
    successful port initialization?

    A. F_Port
    B. E_Port
    C. G_Port
    D. N_Port 
    D
  11. Connecting two switches with the intention of merging them into the same fabric is accomplished
    through which type of port?

    A. F_Port
    B. E_Port
    C. EX_Port
    D. N_Port 
    B
  12. The portshow command output indicates a port as a U_Port type.
    Which three statements are true? (Choose three.)

    A. Port status is unknown.
    B. Nothing is connected to that port.
    C. The port is a user port.
    D. The port is a universal port.
    E. The port can be initialized as an E_Port. 
    BDE
  13. You are connecting a cable between two Brocade 5300 switches, but the switches are not forming
    an ISL between the switches.

    What is the reason?

    A. The ports are set to G_Port.
    B. The ISL ports did not have enough buffer credits configured.
    C. The ports are set to U_Port.
    D. The ports are set to D_Port. 
    D
  14. In the exhibit, what is the result of the fabricprincipal 0 command?

    A. Principal selection mode will be enabled for B6510_B.
    B. Principal selection mode will be disabled for B6510_B.
    C. B6510_B will become the principal switch.
    D. B6510_B will have the highest principal selection priority.    
    B
  15. Which two would be used to synchronize the fabric time? (Choose two.)

    A. Principal switch
    B. Fabric Watch
    C. SMTP
    D. NTP 
    AD
  16. In the exhibit, which device is the Principal switch?

    A. ras001
    B. ras005
    C. ras019
    D. ras047 
    D
  17. Given the fabric output shown in the exhibit, with all fabricprincipal settings the same, which device
    would become the Principal switch in the event of an election?

    A. ras001
    B. ras002
    C. ras005
    D. ras006 
    C
  18. In the exhibit,

    if all switches were operating in insistent Domain ID mode, what would be the result of enabling
    the ICL ports?

    A. DCX1 becomes the Principal switch.
    B. The four-switch fabric does not form.
    C. The four-switch fabric successfully forms.
    D. B5100 becomes the Principal switch. 
    B
  19. What is true of Domain IDs within a fabric?

    A. Domain IDs must be unique.
    B. Domain IDs must be the same.
    C. Domain IDs must be sequential.
    D. Domain IDs must be between 1 and 256. 
    A
  20. Which fabric generic service provides the only service that is user-configurable?

    A. name server (FFFFFC)
    B. fabric controller (FFFFFD)
    C. alias server (FFFFF8)
    D. management server (FFFFFA) 
    D
  21. You remove a switch from the fabric.

    Which well-known address is responsible for notifying the remaining nodes in the fabric of the
    change in topology?

    A. broadcast server (FFFFFF)
    B. management server (FFFFFA)
    C. name server (FFFFFC)
    D. fabric controller (FFFFFD) 
    D
  22. Which fabric generic service will send the time set on the principal or primary Fabric Configuration
    Server (FCS) switch to other member switches in the fabric?

    A. time server (FFFFFB)
    B. clock synchronization server (FFFFF6)
    C. fabric controller (FFFFFD)
    D. broadcast server (FFFFFF) 
    A
  23. To which type of port will the Broadcast Server (FFFFFF) transmit frames?

    A. all N ports regardless of operational status
    B. all N ports in a operational status
    C. all F ports regardless of operational status
    D. all D ports in a operational status 
    B
  24. What are two characteristics of the Name Server (FFFFFC)? (Choose two.)

    A. The service is maintained on each Brocade switch.
    B. The service is maintained solely on the Principal switch.
    C. It maintains the name, address, and capabilities of fabric connected devices.
    D. It maintains the name and address information of fabric connected devices. 
    AD
  25. What is the function of the Fabric Login server (FFFFFE)?

    A. It provides a single point for managing the fabric.
    B. It is responsible for clock synchronization.
    C. It assigns the fabric address to devices attached to a switch granting access to switch services.
    D. It is where fabric/public nodes register themselves and query to discover other devices in the
    fabric. 
    C
  26. In Fabric OS v7.0, which two statements are true about buffer credit recovery? (Choose two.)

    A. Buffer credit recovery is only valid on F or N port types.
    B. You must manually enable it on the port before use on new switch.
    C. Buffer credit recovery is only valid on E port types.
    D. Buffer credit recovery resets the BB counters for the ports. 
    CD
  27. You want to provide full line speed operating at 16 Gbps for a round trip distance of 20 km.

    How many buffers would need to be allocated to each port?

    A. 40
    B. 80
    C. 120
    D. 160 
    B
  28. What are three attributes of buffer-to-buffer credit allocation? (Choose three.)

    A. average frame size
    B. distance
    C. cable optical clarity
    D. link speed

    E. fill word parameters 
    ABD
  29. Which two ELS request and reply sequences advertise buffer-to-buffer credits between Fibre
    Channel devices? (Choose two.)

    A. FLOGI
    B. PLOGI
    C. PRLI
    D. ESC 
    AB
  30. Which two statements concerning Credit Recovery are correct? (Choose two.)

    A. The feature is supported on F_Ports.
    B. The feature allows links to recover after R_RDYs are lost when the credit recovery logic is
    enabled.
    C. The feature uses Fabric Login (FLOGI) to setup Credit Recovery.
    D. During a link reset, the frame and credit loss counters are reset. 
    BD
  31. Which three factors determine if additional buffer-to-buffer credits are required on a link? (Choose
    three.)

    A. frame size
    B. cable core size
    C. link distance
    D. link speed
    E. frame type 
    ACD
  32. You have a 10 km ISL connection between two switches in a fabric. You discovered that the
    E_Port on the remote switch has no more buffer credits available.

    Which two actions must you perform to make this work? (Choose two.)

    A. Check if buffer credit recovery is enabled.
    B. Review your long distance configuration for the remote E_Port.
    C. Review your long distance configuration for the local E_Port.
    D. Increase the maximum payload size to 2112 bytes. 
    AB
  33. What is the purpose of Fibre Channel buffer-to-buffer credit flow control?

    A. to provide in-band management between switches
    B. to provide In Order Delivery (IOD) of SCSI frames
    C. to provide multiple logical data paths across a single physical ISL
    D. to prevent a target device from being overwhelmed with frames 
    D
  34. The performance of an application using remote storage resources across a 20 km ISL is very
    poor, even though the ISL utilization is not very high.

    Which two statements are true about the poor performance? (Choose two.)

    A. Smaller average frame-size requires more buffer credits.
    B. Larger average frame-size requires more buffer credits.
    C. Allocating more buffer credits can increase throughput on an ISL.
    D. Allocating too many buffer credits can decrease throughput on an ISL. 
    AC
  35. Which two statements are true regarding the power supplies for a Brocade DCX 8510-8? (Choose
    two.)

    A. Depending on the blades installed and their respective power requirements, a choice can be
    made between using 1000 Watt or 2000 Watt power supplies.
    B. When using 2000 Watt power supplies, a maximum of two can be inserted into the chassis.
    C. One power supply is required to run the base system with two required for N+1 redundancy.
    D. Two power supplies are required to run the base system with two additional required for N+1
    redundancy. 
    AC
  36. You have a Brocade DCX 8510-8 and want to ensure that the backup CP blade is synchronized
    and available for failover in the event of a failure or planned switchover.

    Which command would you use? 
    A. switchshow
    B. configshow
    C. hashow
    D. switchstatusshow 
    C
  37. Which three statements are true regarding information available through the sensorshow
    command? (Choose three.)

    A. Fan speed is displayed.
    B. Temperature status only is displayed.
    C. Power supply status is displayed.
    D. Power supply voltage is displayed.
    E. Current temperature status is displayed. 
    ACE
  38. What information can be derived from the switchstatuspolicyshow command to explain the
    reported switch state?

    A. the operational status of installed hardware components
    B. the current manually assigned state of switch
    C. the operating parameters required by Brocade for minimum operation
    D. the number of failed components allowed for determining the health of a switch 
    D
  39. Which three tools will allow you to view the current operating statistics of your installed switch port
    SFPs? (Choose three.) 
    A. Host Connectivity Manager
    B. Brocade Network Advisor
    C. Fabric Watch
    D. NET Health
    E. the sfpshow command 
    BCE
  40. Which two features are supported on the Brocade DCX 8510-8? (Choose two.)

    A. 1 Gbps SFP devices
    B. Fibre Channel Loop Protocol devices
    C. FCIP tunnels using an FX8-24 FCIP blade
    D. Integrated Routing (IR) ports 
    CD
  41. The FC8-64 blade uses which type of optical transceiver?

    A. SFP
    B. SFP+
    C. QSFP
    D. mSFP 
    D
  42. The Brocade 1860 Fabric Adapter can be configured to connect to the network using which three
    protocols? (Choose three.)

    A. Ethernet
    B. FCIP
    C. iSCSI
    D. FCoE
    E. iFCP 
    ACD
  43. Which three optical transceivers are supported on 16 Gbps port blades? (Choose three.)

    A. Brocade-branded 4 Gbps SFP
    B. Brocade-branded 8 Gbps SFP
    C. Brocade-branded 10 Gbps SFP
    D. Brocade-branded 16 Gbps SFP
    E. Brocade-branded 64 Gbps QSFP 
    BCD
  44. What is a benefit of using Inter-chassis Link (ICL) connections?

    A. greater distance supported over standard ISL connections
    B. provides connectivity without using user ports
    C. inexpensive connection between chassis-based and departmental switches
    D. combines multiple physical switches to be represented to the fabric as one domain 
    B
  45. Which three statements about the compression feature of Fabric OS v7.0 are true? (Choose
    three.)

    A. A business benefit of compression is improved bandwidth usage on ISLs, especially over long
    distance.
    B. A business benefit of compression is increased bandwidth usage from initiator to storage target.
    C. Compression is mutually exclusive of in-flight encryption.
    D. Compression is supported on E_Ports only.
    E. When compression is enabled, it is a Brocade best practice to configure the long distance ports
    with double the number of buffers. 
    ADE
  46. What are the maximum number of blades that can be inserted in the Brocade DCX 8510-4
    chassis?

    A. 4
    B. 6
    C. 8
    D. 12 
    C
  47. Which feature has been introduced with the Brocade 6510?

    A. local switching
    B. data-at-rest encryption
    C. data-in-flight encryption
    D. port fencing 
    C
  48. Which air flows are available on the Brocade 6510?
    A. back to front only
    B. front to back air flow and back to front airflow depending on the PSU installed
    C. out the side vents to comply with FIPS 140-2 certification
    D. front to back only 
    B
  49. Which direction does the air flow on the Brocade DCX 8510-4?

    A. from the non port side to the port side
    B. from the port side to the nonport side
    C. airflow is reversible depending on the power supply units you have installed
    D. airflow is reversible depending on the blowers you have installed 
    A
  50. Which two features are supported in the Brocade 6510? (Choose two.)

    A. iSCSI
    B. Access Gateway mode
    C. Data Center Bridging
    D. Virtual Fabrics with up to 4 logical switches 
    BD
  51. On the non-port side of the Brocade 6510, if the LED flashes green, which condition does this
    represent?

    A. Power supply or fan is not receiving power or is off.
    B. Power supply or fan is faulty.
    C. Power supply or fan is operating normally.
    D. Environmental range is exceeded. 
    B
  52. What are the physical characteristics of the Brocade 6510?

    A. 1U form factor with 40 ports
    B. 1U form factor with 48 ports
    C. 2U form factor with 48 ports
    D. 2U form factor with 64 ports 
    B
  53. What is the maximum number of virtual channels used per port on the Brocade 16 Gbps ASIC?

    A. 8
    B. 16
    C. 32
    D. 48 
    C
  54. What is the maximum number of ports that the Brocade 6510 switch supports with 16 Gbps optics
    installed?

    A. 12
    B. 24
    C. 40
    D. 48 
    D
  55. At which speeds will a Brocade-branded 16 Gbps FC SFP+ operate?

    A. 4/8/16
    B. 2/4/8/16
    C. 2/4/8/10/16
    D. 1/2/4/8/16 
    A
  56. Which Brocade document provides a standards compliance list, the Brocade DCX8510-8 blade
    support matrix, and the recommended migration paths to Fabric OS v7.0?

    A. Brocade Fabric OS v7.0 Release Notes
    B. Brocade Fabric OS v7.0 Administrators Guide
    C. Brocade DCX8510-8 Hardware Reference Manual
    D. Brocade Fabric OS v7.0 Command Reference Guide 
    A
  57. Which Brocade document will provide steps for power supply removal and replacement for the
    Brocade DCX 8510-8?

    A. Brocade Fabric OS v7.0 Release Notes
    B. Brocade DCX 8510-8 Hardware Reference Manual
    C. Brocade Fabric OS v7.0 Administrators Guide
    D. Brocade Fabric OS v7.0 Troubleshooting Guide 
    B
  58. What are two reasons why you would use the Brocade Compatibility Matrix? (Choose two.)

    A. to review supported MIBs compatible with Brocade FC switches
    B. to review supported commands compatible with Fabric OS v7.0
    C. to review supported tape libraries compatible with Brocade FC switches
    D. to review supported transceivers compatible with Brocade FC switches 
    CD
  59. What information is found in the Brocade DCX 8510-8 Hardware Reference Manual? (Choose
    two.)

    A. configuration techniques of the DCX 8510-8
    B. 16 Gbps compatibility information between the DCX 8510-8 and other vendor hardware
    C. Brocade hardware components of the DCX 8510-8
    D. DCX 8510-8 hardware warranty information 
    AC
  60. Which two documents provide definitions of unknown or unfamiliar output? (Choose two.)

    A. Fabric OS v7.0 Command Reference Guide
    B. Fabric OS v7.0 Administrators Guide
    C. Web Tools v7.0 Release Notes
    D. Fabric OS v7.0 Message Reference 
    AD
  61. Which document provides information on supported configurations for bottleneck detection
    feature?

    A. Fabric OS v7.0 Encryption Administrator's Guide
    B. Fabric OS v7.0 Administrators Guide
    C. Fabric OS v7.0 FCIP Administrators Guide
    D. Fabric OS v7.0 Release Notes 
    B
  62. Which document describes open and closed Fabric OS v7.0 defects?

    A. Fabric OS v7.0 Administrators Guide
    B. Fabric OS v7.0 Message Reference
    C. Fabric OS v7.0 Troubleshooting and Diagnostics Guide
    D. Fabric OS v7.0 Release Notes 
    D
  63. Which document provides instructions on how to use the new features found in Fabric OS v7.0?

    A. Fabric OS v7.0 Message Reference
    B. Fabric OS v7.0 Troubleshooting and Diagnostics Guide
    C. Fabric OS v7.0 Administrators Guide
    D. Fabric OS v7.0 Release Notes 
    C
  64. Which document describes the acceptable environmental ranges for both operating and
    nonoperating (such as during transportation or storage) conditions for the Brocade 6510?

    A. 6510 Hardware Reference Manual
    B. 6510 Quickstart Guide
    C. 6510 Combined Power Supply and Fan Assembly Replacement Procedure Guide
    D. Fabric OS v7.0 Administrators Guide 
    A
  65. Prior to enabling in-flight encryption, which feature must also be enabled?

    A. authentication policy
    B. DCC security policy
    C. SCC security policy
    D. FCS policy 
    A
  66. Which three statements about the switch audit log are true? (Choose three.)

    A. By default, all event classes are configured for audit.
    B. Audited events have no negative impact on performance.
    C. Audited events are streamed to the fabric Management Server.
    D. If too many events are generated by the switch, audit events are dropped by Fabric OS.
    E. Audit events are lossless if the system message log and IP network facilities fail. 
    ABD
  67. What are two reasons you would use a fabric name? (Choose two.)

    A. to change the Principal switch parameter within a fabric
    B. for ease of management
    C. to replace the Fabric ID (FID) parameter
    D. for unified representation on all switches within one fabric 
    BD
  68. What is the default IP address assigned to a new Brocade switch?

    A. 10.1.1.1
    B. 10.10.10.1
    C. 10.77.77.1
    D. 10.77.77.77 
    D
  69. You have set the timeout command value to zero (0).
    How will this affect the switch?

    A. The R_A_TOV and E_D_TOV values will be set to zero.
    B. The R_A_TOV and E_D_TOV values will be ignored.
    C. The R_A_TOV and E_D_TOV values will be set to factory defaults.
    D. After logging in, the telnet session will remain open. 
    D
  70. What are the proper steps to set the time and date and synchronize a switch with an external time-
    based reference?

    A. Set the time and date using the tstimezone command, then set the time synchronization using
    the tsclockserver command.
    B. Set the time and date using the tsclockserver command, then set the time synchronization
    using the tstimezone command.

    C. Set the time and date using the date command, then set the time synchronization using the
    tsclockserver command.
    D. Set the time and date using the mstdenable command, then set the time synchronization using
    the tstimezone command. 
    C
  71. What is the purpose of the syslogdfacility command?

    A. It defines the severity level of the syslog messages.
    B. It defines the destination server of the syslog.
    C. It groups together log messages from related switches.
    D. It defines the reporting schedule of the syslog facility. 
    C
  72. A customer is using the portcfgoctetspeedcombo command.
    Which two statements are true? (Choose two.)
    A. This command only works on Condor 2-based platforms.
    B. This command works on both Condor 2 and Condor 3-based platforms.
    C. Speeds that can be configured include both 10 Gbps and 16 Gbps.
    D. The speed combination set on a given port will be applied to all ports in the configured port's
    octet. 
    CD
  73. What are the correct serial port settings for establishing a console port session to a Brocade
    Fabric OS-based switch?

    A. 9600, 8, N, 1 no flow control
    B. 19200, 8, N, 1 no flow control
    C. 9600, 8, N, 1 hardware flow control
    D. 19200, 8, N, 1 hardware flow control 
    A
  74. A customer is using the passwdcfg command to modify the password policies in their SAN?
    Which three statements regarding this command are true? (Choose three.)

    A. The command allows you to configure account lockout policies.
    B. The command allows you to configure account expiration policies.
    C. The command allows you to change the passwords on user accounts.
    D. The command allows you to modify password strengths.
    E. The command does not allow you to modify password strengths. 
    ABD
  75. A customer is replacing a failed switch. The configdownload command is used to restore the
    original switch's configuration information onto the replacement switch.

    Which switch parameter must still be configured manually?

    A. Domain ID
    B. E_D_TOV
    C. MAX_HOPS
    D. switch name 
    D
  76. A customer uses the following command when attempting to upgrade the firmware to Fabric OS
    v7.0 on a Brocade 6510 switch: firmwaredownload –U /usb/usbstorage/brocade/firmware/v7.0.

    What are two possible reasons for the download failing? (Choose two.)

    A. The USB port has not been enabled on the Brocade 6510.
    B. The customer FTP server has not been setup properly.
    C. The USB stick is not a Brocade-branded device.
    D. The firmware must be placed in the /usb/firmwaredownload directory. 
    AC
  77. A customer is setting up a pair of Brocade 6510s with Fabric OS v7.0 and they are interested in
    using their in-flight encryption and compression capabilities.

    Which two statements regarding these capabilities are true? (Choose two.)

    A. No more than two ports on a Brocade 6510 can be configured with encryption, compression, or
    both.
    B. All ports on a Brocade 6510 can be configured with encryption, compression, or both.
    C. Encryption and compression can be enabled simultaneously on an ISL.
    D. The encryption and compression features are licensed. 
    AC
  78. A customer is attempting to setup a 10 Gbps link between two datacenters. A Brocade DCX 8510-
    8 fully populated with FC16-48 blades is installed at each datacenter.

    Which two statements regarding setup requirements are true? (Choose two.)

    A. Each Brocade DCX 8510-8 must have the High Performance Extension over FCIP/FC license
    installed.
    B. Each Brocade DCX 8510-8 must have the 10 GbE FCIP/10G Fibre Channel license installed.
    C. The portcfgoctetspeedcombo is required to configure the 10 Gbps speed capabilities.

    D. The portcfgoctetspeedcombo is not required because each port on a 16 Gbps blade supports
    both 10 and 16 Gbps speeds. 
    BC
  79. You have multiple Brocade DCX-8510-8s connected together using ICL cables. The administrator
    is receiving complaints that only eight of the 16 ICL links are activated on a particular core blade.

    What should be installed on both DCXs?

    A. Brocade ISL Trunking license
    B. Full Fabric license
    C. Inter Chassis Link (2nd POD) license
    D. ICL 16-link license 
    C
  80. An administrator needs to set a message on an upcoming security audit every time someone logs
    into a switch.

    Which two commands can be used to set this message? (Choose two.)

    A. bannerset
    B. motd --set
    C. auditcfg
    D. secpolicycreate 
    AB
  81. Which two Fabric OS rules apply for password changes? (Choose two.)

    A. The user of the Administrator group needs to be logged in using SCP.
    B. The user of the Administrator group can change the User group password.
    C. To change a user’s password, at least one character must be changed.
    D. The user of the Operator group can change the User group password. 
    BC
  82. Which long distance port configuration value allows the switch to automatically assign buffer-to-
    buffer credits according to the link length?

    A. L0
    B. LE
    C. LD
    D. LS 
    C
  83. Which two statements are true about Brocade RBAC? (Choose two.)

    A. Access levels for the roles may be set.
    B. Permission by class may be set.
    C. Access can be controlled by modifying the predefined roles.
    D. Access can be controlled by modifying the predefined classes. 
    AB
  84. An administrator has just added a Fabric license to a switch. The features of this license did not
    become activated after the license was added.

    Which action would correct this problem?

    A. The switch needs to be rebooted.
    B. They must do a switchdisable followed by a switchenable.
    C. The ports must be disabled and then re-enabled.
    D. The Fabric license must be reinstalled. 
    A
  85. An administrator wants the time for all switch logs in the fabric to be based on a reliable time
    server.

    Which action would accomplish this goal?

    A. Synchronize the time of all switches to an LDAP server.
    B. Configure the Principal switch to point to a NTP server.
    C. Configure all switches individually to synchronize with a RADIUS server.
    D. Use Brocade Network Advisor to synchronize its time with all of the switches in the fabric. 
    B
  86. How can you enable a Brocade-branded USB memory stick that has been plugged into a USB
    port on a switch?

    A. Use the firmwaredownload command.
    B. Use the chassiscfg command.
    C. Detection and mounting of the inserted USB device is automatic.
    D. Use the usbstorage -e command. 
    D
  87. What is the default behavior when using the firmwaredownload command to upgrade firmware on
    a Brocade DCX 8510-8?

    A. It will download firmware to the secondary partition on both CPs and requires a manual reboot.
    B. The firmware download automatically updates the firmware on both CPs.
    C. The firmware is only downloaded to the standby CP.
    D. The firmware is only downloaded to the active CP. 
    B
  88. An administrator has a Universal Time Based License that has expired.

    What are two ways that the administrator can extend the features included in this Universal Time
    Based License? (Choose two.)
    A. Remove then re-install the Universal Time Based License.
    B. Add a temporary license with an expiration date after the Universal Time-based license expired
    date.
    C. Add a permanent license key.
    D. Backdate the date on the switch. 
    BC
  89. After adding a Trunking license to the Brocade 6510, which two command sequences can be
    issued to activate the license? (Choose two.)

    A. Issue the commands switchdisable;switchenable.
    B. Issue the commands licenseadd;licensshow.
    C. Issue the commands portdisable;portenable.
    D. Issue the commands licenseport;licenseadd. 
    AC
  90. You want to upgrade your production SAN with four Brocade DCX-4Ss to Fabric OS v7.x with a
    single Fabric OS CLI command on every Director.

    Based on Brocade best practice, what are three highly recommended actions to perform the
    upgrades? (Choose three.)

    A. Use a telnet session to the standby CP to perform the firmwaredownload command.
    B. Reference the corresponding Fabric OS v7.x release notes for possible updates.
    C. Use the hashow command for CP sync-status verification.
    D. Use SFTP protocol to the DCX-4S or use the USB device.

    E. Verify the current Fabric OS version, because Brocade does not support online upgrades from
    more than one previous release. 
    BCE
  91. A licenseshow output on Fabric OS v7.0 shows the text Obsolete License.
    Which statement is true?

    A. A multiple feature license key has overwritten a single feature license key.
    B. A feature license key is installed twice and one is flagged obsolete.
    C. A temporary license is expired.
    D. The feature no longer requires a license key, but the license key is still installed. 
    D
  92. What is the benefit of having a chassis IP address on a Brocade DCX 8510-8 in addition to the
    dedicated CP0 and CP1 IP addresses?

    A. Only the chassis IP address supports IPv6.
    B. Only the chassis IP address supports DHCP.
    C. The chassis IP address can be in a different IP subnet. (other than CP0/1 subnet).
    D. You can manage the Brocade DCX 8510-8 without knowing which is the active CP. 
    D
  93. What is the total number of IP addresses that are used on a Brocade DCX 8510-8 chassis?

    A. 3
    B. 4
    C. 5
    D. 6 
    A
  94. You have been asked, for security reasons, to turn off telnet and Web Tools on your Brocade DCX
    8510s.

    Which tool do you use?

    A. SNMPv3
    B. RBAC
    C. IPsec policy
    D. IPFilter policy 
    D
  95. You need to trunk two ISLs over 100 km apart at full bandwidth.

    Which two actions are required? (Choose two.)

    A. Configure the portcfgdport to 1.
    B. Apply a Trunking license.
    C. Install an Extended Fabrics license.
    D. Set the VC translate link to 0. 
    BC
  96. In the exhibit, you are connecting two Brocade DCX 8510-8 chassis together using ICL ports.    

    Which statement is true?

    A. As cabled, each core blade provides one 128 Gbps trunk.
    B. As cabled, each core blade provides two 64 Gbps trunks.
    C. As cabled, each core blade provides four 32 Gbps trunks.
    D. As cabled, each core blade provides eight 16 Gbps trunks. 
    C
  97. Which action will cause the link cost of a path to change when the path contains a trunk?

    A. ISLs are added to a trunk in the path.
    B. A switch is added in the path.
    C. The trunk port speeds are changed from 8 Gbps to 16 Gbps.
    D. A trunk member port is disabled. 
    B
  98. What does a deskew value of 30 using trunkshow represent?

    A. The associated ISL is 30 meters longer than the trunk master.
    B. The associated ISL is 30 meters longer than the shortest ISL of the trunk.
    C. The associated ISL is 300 meters longer than the trunk master.
    D. The associated ISL is 300 meters longer than the shortest ISL of the trunk. 
    B
  99. Referring to the exhibit, which two statements explain why the ISL is the trunk master? (Choose
    two.)

    A. The ISL connected to Port 0 is the trunk master because it has the lowest port number.
    B. The ISL connected to Port 0 is the trunk master since it has the highest deskew value.
    C. The ISL connected to Port 0 is the trunk master since it was the first to initialize the ISL.
    D. The ISL connected to Port 0 is the trunk master since the original trunk master was disabled
    and re-enabled. 
    CD
  100. Which three statements are true for ICL connections between two Brocade DCX 8510-8s?
    (Choose three.)

    A. The maximum number of QSFP cables between two chassis is eight.
    B. The minimum supported number of QSFP cables between two chassis is four.
    C. The maximum number of QSFP cables between the two chassis is sixteen.
    D. The principal switch is allowed to have five cables on the core blade in slot four.
    E. QSFP cables need to be connected to the same blade of its neighbor. 
    ABE
  101. Which two statements are true about Brocade masterless trunking when the trunk master fails or
    is disabled? (Choose two.)
    A. The trunk is not used for traffic until the new master is selected and the routes are updated.
    B. The new master acquires all the configurations of the old master.
    C. Bottleneck detection on the trunk will not resume until configured on the trunk.
    D. Trunk monitoring is configured on the master port. 
    BD
  102. In the exhibit, all ISLs are running at 16 Gbps. 30 initiators are connected to 30 targets, and port-
    based routing with DLS is configured. 


    How many initiators use "Path a" for outbound traffic?

    A. 10
    B. 15
    C. 20
    D. 30 
    C
  103. You add a second ISL between two switches, but they do not form a trunk.
    Which three actions should be taken to determine the reason? (Choose three.)

    A. Verify if the link speed is equal on both ISLs.
    B. Verify if the Trunking license is installed.
    C. Verify if the first ISL is configured as the master ISL.
    D. Verify if both ISLs are configured to the same deskew value.
    E. Verify if trunking is enabled on all four ports. 
    ABE
  104. You want to implement trunking on a 40-port Brocade 5100 switch.

    What are the maximum number of ISL trunks possible?

    A. 4
    B. 5
    C. 19
    D. 20 
    D
  105. You want to maximize your bandwidth between two Brocade DCX 8510-8s within a single ISL
    trunk group between user ports.

    What is the maximum throughput?

    A. 32 Gbps
    B. 64 Gbps
    C. 128 Gbps
    D. 256 Gbps 
    C
  106. You need to verify your trunking configuration with the trunkshow command.
    What information can you obtain from the command output? (Choose three.)

    A. Which ISLs are in an ISL trunk.
    B. How many ISL trunks are on that switch.
    C. If the Trunking license is installed.
    D. If masterless trunking is enabled.
    E. The deskew value for each ISL that is in an ISL trunk. 
    ABE
  107. You already use ICLs in your Brocade DCX 8510-8 fabric and want to use ICL trunking.
    Which statement is true?

    A. Install Trunking licenses on all DCX with ICL connections.
    B. No action is required since ICL trunking is always enabled.
    C. Install ICL licenses on all DCXs with ICL connections.
    D. Use the portcfgtrunkport command to enable trunking on all ICL ports. 
    B
  108. You have a four-port trunk with deskew values of 45, 35, 20, and 15.

    Which statement about the deskew values is correct?

    A. The difference in deskew values indicate greater bandwidth.
    B. The difference in deskew values indicate the trunk priority.
    C. The difference in deskew values indicate trunk configuration mismatches.
    D. The difference in deskew values indicate cable length differences. 
    D
  109. You are trying to trunk port 8 and 9 together, but the trunk is not forming.
    Referring to the exhibit, what is the problem?

    A. Port speeds are different in the trunk group.
    B. The ports are not in the same trunk group.
    C. Long distance is enabled in the trunk group.
    D. Trunking is not enabled on all ports in the trunk group. 
    D
  110. You need to form a trunk between a Brocade 6510 and a Brocade 5100.

    What are two ways that this trunk can form? (Choose two.)

    A. The ports must be in the same trunk group.
    B. The ports must be in different trunk groups.
    C. The ports must auto-negotiate down to a speed of 4 Gbps.
    D. The ports are set to the same speed. 
    AD
  111. On your Brocade 6510, you have enabled trunking on ports 0-7. When the trunks form on ports 0-
    7 with a Brocade 5100, you notice that there are two trunks even though the speed and distances
    are the same.

    Why have two trunks formed?

    A. Some of the ports are G_Ports.
    B. Some of the ports have QoS enabled.
    C. Some of the ports are in different trunk groups.
    D. All of the ports are not in ISL R_RDY mode.
    B
  112. What is the method used to determine the least cost for delivering frames between switches in a
    fabric?

    A. Dynamic Path Selection
    B. Dynamic Load Sharing
    C. Fabric Shortest Path First
    D. Open Shortest Path First 
    C
  113. You have run the following Fabric OS v7.0 command: dlsset --enable -lossless.
    Which two affects will this have on the fabric? (Choose two.)

    A. Path selection will now be determined by the last port used algorithm.
    B. You may now configure static routes with an exchanged-based routing policy.
    C. Ensures frames cannot be discarded during a rebalance of ISLs.
    D. Enables dynamic rebalancing on a group of ISLs. 
    CD
  114. You must display fabric topology information to evaluate your fully populated fabric.
    Which two commands will display this information? (Choose two.)

    A. urouteshow
    B. dlsshow
    C. iodshow
    D. fabricshow 
    AD
  115. Due to technical limitations of your customer's storage systems, you must use port-based routing
    in the production fabric.

    Which two statements are true? (Choose two.)

    A. The input port from the source is assigned to an output port toward the destination switch.
    B. Routes are allocated using round-robin assignments.
    C. Routes are allocated using exchange-based routing assignments.
    D. The input port from the source is assigned to multiple output ports toward the destination
    switch. 
    AB
  116. You want to use exchange-based routing to optimize ingress frame path utilization.
    Which three attributes help choose the path? (Choose three.)
    A. S_ID for this frame
    B. D_ID for this frame
    C. RX_ID for this frame
    D. SEQ_ID for this frame
    E. OX_ID for this frame 
    ABE
  117. You have changed the routing policy from port-based routing to exchange-based routing in your
    fabric.

    Which statement is true?

    A. DLS is disabled by default and cannot be enabled.
    B. DLS is enabled by default and cannot be disabled.
    C. DLS is not required.
    D. DLS only works with port-based routing. 
    B
  118. Your customer wants to apply the exchange-based routing policy to the fabric.
    Which statement is true?

    A. Each switch has its own routing policy.
    B. Each switch has a fabric-wide routing policy.
    C. Exchange-based policy replaces the port-based policy fabric-wide.
    D. Port-based policy can coexist with exchange-based policy on different blades in a Brocade
    Director. 
    A
  119. In the exhibit, which two statements about the output are true? (Choose two.)

    A. Input ports are assigned to a single output port.
    B. Port-based routing policy is in place.
    C. Input ports are assigned to multiple output ports.
    D. Exchange-based routing policy is in place. 
    CD
  120. You are using two 16 Gbps and two 8 Gbps ISLs to connect two Brocade DCX 8510-8s.
    Which statement is true?

    A. Default link cost of the 8 Gbps links is 250.
    B. Default link cost of the 16 Gbps links is 250.
    C. Default link cost of all links is 500.
    D. Default link cost of all links is 1000. 
    C
  121. What information will be obtained running the pathinfo command on a Brocade switch?

    A. routing information from a source port on the local switch to a destination port on the local
    switch
    B. routing information from a fabric topology as it appears to the local switch
    C. routing information from a fabric topology as it appears to the remote switch

    D. routing information from a source port on the local switch to a destination port on another switch 
    D
  122. You want to use a port-based routing policy.
    Referring to the exhibit, which statement is true?

    A. You are already using the port-based routing policy.
    B. You need to disable the switch before changing the routing policy.
    C. You need to reboot the switch after changing the routing policy.
    D. You need to fastboot the switch after changing the routing policy. 
    B
  123. A switch administrator queries two Brocade switches connected together for the aptpolicy and
    receives the same following output from both switches: Current Policy: 3 0(ap)

    Which two conclusions can be made about the Brocade fabric? (Choose two.)

    A. DLS cannot be disabled on either switch.
    B. The ISL routes will never change in the event an ISL is disabled or fails.
    C. Frames from different exchanges in a fabric may be assigned to different egress ISL ports.
    D. Frames from the same exchange in a fabric may be assigned to different egress ISL ports. 
    AC
  124. What correctly describes the attributes of Brocade’s in order delivery when enabled?

    A. Enforces in order delivery of frames during a fabric topology change.
    B. Ensures lossless failover.
    C. Ensures that an equal number of frames cross each ISL.
    D. Enforces in order delivery of frames in a stable fabric environment. 
    A
  125. Which statements are true about DLS? (Choose two.)

    A. DLS cannot be disabled when using port-based routing.
    B. There is a recalculation of routes when an ISL is disabled or enabled.
    C. DLS cannot be disabled if exchanged-based routing is enabled.
    D. The switch has to be disabled to enable DLS. 
    BC
  126. You have been asked to create a new zone name in your fabric.

    Which name is valid?

    A. zone_123server
    B. 123server_zone
    C. zone-123server
    D. 123server-zone 
    A
  127. You changed the effective zone configuration to add new devices.
    Which command will save, enable, and activate the new zoning configuration?

    A. cfgactvshow
    B. cfgenable "cfgname"
    C. zone --activate "name"
    D. zoneadd "zoneName" 
    B
  128. With default zoning configured as allaccess, a customer has disabled the zoning configuration on the fabric. What will happen to the fabric?
    A. Only those devices that were in zones will not be able to talk to another device.
    B. Only those devices that have not been zoned will not be able to talk to another device.
    C. No devices will be able to talk to each other.
    D. All devices will be able to talk to each other.
    D
  129. What are three different types of zoning that can be implemented to provide additional fabric
    services? (Choose three.)

    A. LSAN zones
    B. DPR zones
    C. TI zones
    D. QoS zones
    E. FCR zones 
    ACD
  130. You want to provide secure access from host to storage and minimize RSCN propagation to
    affected devices during fabric events.

    What is the Brocade recommended zoning strategy to accomplish these goals?

    A. Create a zone for each host to any target.
    B. Create a zone for all hosts to all targets.
    C. Create zones for all hosts to each target.
    D. Create a zone with no more than 10 hosts and 10 targets. 
    A
  131. In a Brocade 16 Gbps fabric, how many zone configurations can be active at one time?

    A. 1
    B. 16
    C. 32
    D. 128 
    A
  132. A customer issues the defzone --noaccess command followed by cfgsave on one switch in their
    ten-switch fabric.

    Which two statements are true? (Choose two.)

    A. If cfgdisable is executed, all SAN devices will be able to communicate with one another.
    B. If cfgdisable is executed, all SAN devices will not be able to communicate with one another.
    C. This command sequence must be issued on every switch in the fabric.
    D. This command sequence only has to be issued on one switch in the fabric. 
    BD
  133. A customer wants to enable a new zoning configuration without risking downtime to FC
    communications in the fabric.

    Which statement is true?

    A. The cfgenable command should be used to apply the new configuration.
    B. The cfgdisable command must be issued followed by the cfgenable command.
    C. The customer must modify their default zoning policy and then enable the new zoning
    configuration.
    D. The customer must modify their default zoning policy, then disable their zoning configuration
    before enabling. 
    A
  134. A SAN consists of devices A, B, C, D, and E. On the SAN, there is a single zone in the effective
    configuration consisting of zone members A, B, and C. The default zoning mode on the fabric is
    set to "allaccess".

    Which two statements are true? (Choose two.)

    A. Devices D and E will be able to communicate with one another.
    B. Devices D and E will not be able to communicate with one another.
    C. Devices D and E will not be able to communicate with devices A, B, and C.
    D. Devices D and E will be able to communicate with devices A, B, and C but only session-based
    zoning will be enforced. 
    BC
  135. Which two statements regarding Traffic Isolation (TI) zones are true? (Choose two.)
    A. A TI zone can have failover enabled or disabled.
    B. TI zones only include edge ports and never E_Ports.
    C. TI zones are created using the zonecreate command.
    D. TI zones will only appear in the defined zoning configuration. 
    AD
  136. To enable cloud services in your SAN, you want to use fabric-assigned WWNs.
    Which two statements are true? (Choose two.)

    A. All switches and Directors must be 16 Gbps devices.
    B. You can replace failed HBAs within a server, without having to change any zoning or LUN
    mapping configurations.
    C. FA-PWWN is supported only on Brocade HBAs.
    D. Automatically assigned FA-PWWNs are only unique on a single switch. 
    BC
  137. What is a group of one or more zones called?

    A. a zone alias
    B. a zone configuration
    C. a zone series
    D. a zone group 
    B
  138. You want to implement hardware enforced (frame-based) zoning.

    What is required?

    A. All members of a zone must not use an alias.
    B. All members of a zone must be identified using WWNs.
    C. All members of a zone must be identified by domain,port-address.
    D. All members of a zone must be identified the same way, either using WWNs or domain,port-
    address, but not both.
    D
  139. Exhibit:



    which two statements are true? (Choose two.)

    A. Device 44,5 and 3,4 can access each other.
    B. Device 1,2 and 3,4 can access each other.
    C. Zone blue is session-based hardware enforced.
    D. Zone red is session-based hardware enforced. 
    BC
  140. Which three statements are true about device zoning? (Choose three.)    
    A. WWN zones are software enforced zones.
    B. Zones can overlap on target devices.
    C. Zones can overlap on initiator devices.
    D. At least one zone is required in a fabric.
    E. Single HBA zoning is a Brocade best practice and the preferred method. 
    BCE
  141. Which two are considered Brocade's recommended best practice for creating zones? (Choose
    two.)

    A. Define a zone as one initiator to many targets per zone.
    B. Define a zone as multiple initiators to many targets per zone.
    C. Always implement zoning even if LUN masking is used.
    D. Never implement zoning when LUN masking is used. 
    AC
  142. You created a new zoning configuration, REDzone, to replace BLUEzone, enabled it, and it failed.
    What is the state of your effective zoning configuration for your fabric?

    A. There is no effective zoning configuration because the REDzone configuration failed.
    B. The effective zoning configuration is REDzone.
    C. The effective zoning configuration is still BLUEzone because the REDzone configuration failed.
    D. The effective zoning configuration is set to all access because the REDzone configuration
    failed. 
    C
  143. You are installing an existing switch into a different fabric. You need to clear the zoning database
    so that it will merge seamlessly into the existing fabric.

    Which command sequence do you need to perform to accomplish this task?

    A. cfgdisable; cfgclear; cfgsave
    B. cfgdisable; cfgsave; cfgclear
    C. zonedelete; zonecreate; zoneadd
    D. zonedelete; zonecreate; zoneadd; cfgenable 
    A
  144. Which three management methods can be blocked using the ipfilter command? (Choose three.)

    A. telnet
    B. FTP
    C. console serial port
    D. HTTP
    E. USB 
    ABD
  145. Which two statements are true regarding HTTPS? (Choose two.)

    A. HTTPS can be blocked using the ipfilter command.
    B. HTTPS can be configured using security policies on the switch.
    C. HTTPS first must be enabled through the serial port.
    D. SSL needs to be enabled with a certificate. 
    AD
  146. How can you unblock telnet access when a rule is in place to disable it?

    A. Issue the ipfilter --delete from the serial port.
    B. Perform a fastboot using SSH.
    C. Use secpolicydelete from the serial port.
    D. Reset the ACL policies with the secpolicyset command using SSH. 
    A
  147. You want to disable certain non-secure management interfaces on your switches.
    Which two interfaces would you consider disabling? (Choose two.)

    A. SNMP
    B. SCP
    C. SSH
    D. HTTP 
    AD
  148. Which two statements are true about implementing HTTPS on Brocade switches? (Choose two.)

    A. Fabric OS uses secure socket layer (SSL) to support HTTPS.
    B. HTTPS uses public-key cryptography to authenticate the remote computer.
    C. A certificate must be generated and installed on each switch to enable SSL.
    D. A public key needs to be generated and placed on the switch and client. 
    AC
  149. What are two secure methods to perform a file transfer of configuration files from the switch?
    (Choose two.)

    A. Use the USB interface.
    B. Use the SCP protocol.
    C. Use the SSH protocol.
    D. Use the SNMP protocol. 
    AB
  150. Which two statements are true about using FTP to download firmware to a switch? (Choose two.)

    A. The FTP server service needs to be running on the host.
    B. FTP is an option in the firmwaredownload command.
    C. FTP must be enabled on a switch using the configure command.
    D. FTP requires that a common public key be installed on the host and switch. 
    AB
  151. Which two statements are true about using SFTP for firmware downloads? (Choose two.)

    A. SFTP is an option in the firmwaredownload command.
    B. Public keys need to be exchanged between the switch and host.
    C. Private key certificates need to be installed on the switch.
    D. SSH must be running on the host. 
    AD
  152. Which three statements are true about using SCP on Brocade switches? (Choose three.)

    A. SCP can be used to perform configuploads and configdownloads.
    B. SCP can be used for downloading firmware.
    C. SCP can be used for installing certificates to a switch.
    D. SCP uses RADIUS authentication.

    E. SCP is configured as a security policy on a switch. 
    ABC
  153. You need a tool that can manage basic zoning and perform basic switch configurations.
    Which two tools will provide these capabilities? (Choose two.)

    A. Web Tools
    B. SAN Health
    C. Brocade Network Advisor
    D. SAN Health Diagnostics Capture 
    AC
  154. You need to generate a topology of your fabric with historical performance data.
    Which two tools will provide this? (Choose two.)

    A. Web Tools
    B. Brocade Network Advisor
    C. Brocade SAN Health Professional
    D. Brocade SAN Health Diagnostics Capture 
    BC
  155. You need a single management solution for data, storage, application delivery, wireless, and
    converged networks.

    Which tool provides all of these solutions?

    A. Web Tools
    B. SAN Health
    C. DCFM
    D. Brocade Network Advisor 
    D
  156. You want a dashboard to show fabric events, SAN and IP switch inventory, and SAN operational
    status.

    Which tool will provide this data?

    A. Web Tools
    B. SAN Health
    C. Brocade Network Advisor
    D. SAN Health Diagnostics Capture 
    C
  157. You enable the Fabric OS v7.0 thmonitor command.
    What is being monitored?

    A. power supply temperature
    B. blade thermal state
    C. 16 Gbps SFP variables
    D. fan temperature 
    C
  158. Which management utility would you use to verify the link status and perform Ethernet loopback
    tests during installation of the Brocade 1020 CNA?

    A. Host Connectivity Manager
    B. Web Tools
    C. Fabric Watch
    D. Brocade IronView Network Manager 
    A
  159. You have added three new host devices to an existing switch and would like to see a real time
    representation of the activity on these newly connected ports.

    What are two ways to accomplish this? (Choose two.)

    A. Select the Performance Monitor tab in the Web Tools utility, and choose the slot/port of the
    devices to view.
    B. Run a NET Health report, including the newly attached ports and view it.
    C. Run the portperfshow command in recursive mode.

    D. Save the output of the configupload to the USB port, and view the activity from a desktop. 
    AC
  160. You want to upgrade the firmware within your 16 Gbps fabric during a planned change control
    window.

    Which two Brocade tools could you use to complete this task? (Choose two.)

    A. SAN Health
    B. Brocade Network Advisor
    C. Fabric Watch
    D. Web Tools 
    BD
  161. Your manager wants you to provide a detailed report of your fabric including a spreadsheet
    breakdown of devices as well as a Visio diagram.

    Which Brocade tool would complete this task for you?

    A. Brocade Network Advisor
    B. Fabric Watch
    C. SAN Health
    D. Web Tools 
    C
  162. You need to install and configure a Brocade 1860 Fabric Adapter in your host.
    Which two Brocade tools could be used to configure it for fabric connectivity? (Choose two.)

    A. SAN Health
    B. Brocade Network Advisor
    C. Host Connectivity Manager
    D. Web Tools 
    BC
  163. You have two fabrics that need to merge. Switch A’s and Switch B's zoning configuration have the
    same content, but different effective configuration names.

    What will happen?

    A. Both switches will have the same effective configuration.
    B. Fabric segments due to a zone conflict configuration mismatch.
    C. Switch A will use the configuration from Switch B.
    D. Fabric segments due to a zone conflict content mismatch. 
    B
  164. You have been asked to upgrade your Brocade DCX from Fabric OS v6.4 to Fabric OS v7.0 using
    FTP. The upgrade fails each time you try and you have verified that both CPs have been firmly
    inserted into the chassis.

    Which two statements explain why the firmware download is failing? (Choose two.)

    A. Both CPs' management interfaces are not plugged into the management network.
    B. You cannot upgrade directly to Fabric OS v7.0.
    C. There is an FS8-18 blade in the chassis.
    D. There is an FR4-18i blade in the chassis. 
    AD
  165. You are troubleshooting a server connected to a Brocade 6510. The server is not logging into the fabric and you need to escalate the problem to support.
    What information should be gathered for the support team? (Choose three.)

    A. fabricshow output
    B. supportsave output
    C. detailed description of the problem
    D. HBA model and drivers
    E. storage LUN masking configuration
    BCD
  166. You attempt to merge two fabrics. The merge fails and results in a fabric segmentation.
    Which three reasons may cause the two fabrics to segment? (Choose three.)

    A. conflicting Domain ID
    B. both fabrics having a Fabric ID value of 100
    C. zoning configuration issue
    D. fabric name conflict
    E. security policies 
    ACE
  167. What are two factors that the SAN administrator must consider when adding a switch to an
    existing non-routed fabric running Fabric OS v7.0? (Choose two.)

    A. incompatible fabric parameters
    B. incompatible chassis configuration
    C. Fabric ID entries
    D. different zoning configuration entries 
    AD
  168. You have attached a legacy 4 Gbps storage device to your new Brocade 6510 switch. The
    switchshow output for that port shows the state of the port as a G_port.

    What is the cause of the problem?

    A. Insufficient buffer credits are defined on the legacy storage device.
    B. There is a fabric zoning device definition error.
    C. The storage device driver does not provide correct fabric login (FLOGI) parameters.
    D. The switch port is persistently disabled. 
    C
  169. You have attached a host to a fabric. The host switch port shows as F_Port. You have zoned the
    new device, saved, and activated the new zoning information. The host is not able to communicate
    with the storage. 


     How would you validate the zoning and FC communication end-to-end?

    A. On switch FAB_A, run the islshow, followed by the portdportest commands; perform the same
    set of tests from switch FAB_B.
    B. On switch FAB_A, verify the entry in the name service for device 21:00:00:20:37:e1:33:40;
    verify the zoning database for the correct alias assigned to the storage device.

    C. On switch FAB_B, verify the entry in the name service for device 10:00:00:00:c9:2a:b6:9e;
    verify the zoning database for the correct alias assigned to the host device.
    D. On either switch in the exhibit, run the fcping command with the WWNs as the arguments. 
    D
  170. You are experiencing performance problems on your Brocade 6510 switch.
    Which command would you run before troubleshooting the problem?

    A. errdump
    B. portcfgshow
    C. fabricshow
    D. supportsave 
    D
  171. After upgrading your SAN to newer 16 Gbps switches, performance has suffered for some hosts.
    You have enabled bottleneck monitoring using the latency parameter and see the console
    message shown:

    Severe latency bottleneck detected at slot X port Y
    Which two changes should you make to your SAN to resolve the problem? (Choose two.)

    A. Evaluate the slower 2/4 Gbps legacy devices in the SAN for upgrade or removal.
    B. Consolidate any legacy hosts with a storage port to one ASIC on one blade to minimize traffic through the fabric.
    C. Increase the buffers on the faster storage ports to accommodate the greater traffic; then
    decrease the buffers on the slower devices.
    D. Decrease the buffers on the faster storage ports to limit the greater traffic; then increase the
    buffers on the slower devices. 
    AB
  172. After upgrading a SAN to new 16 Gbps switches in your existing facility, the interswitch
    performance has not improved. You would like to perform connection and stress testing on the
    new 16 Gbps ISLs. You want to run the portdporttest command.

    What must be completed before this command can be run?

    A. The port must be set to loopback.
    B. The port must be set to debug mode.
    C. The port must be configured to E_Port.
    D. The port must be disabled and configured to D_Port. 
    D
  173. You are attempting to gather information from the switch using the USB port. After connecting your
    laptop to the switch's USB port using a USB cable, the device manager on the laptop will not open
    a CLI session to the switch.

    What would cause this error?

    A. The switch's USB only supports Brocade branded USB memory sticks.
    B. The laptop does not have the latest USB driver for the Brocade switches.
    C. The USB cable must be a Brocade branded cross-over type, supplied with the switch.
    D. The switch USB supports only type 1 USB devices. 
    A
  174. You have upgraded your SAN to new 16 Gbps switches in a legacy data center and are
    concerned about the quality of your cabling and patch panels. You would like to view a snapshot
    of the link layer errors, Class 3 discards, and TX/RX values.

    Which command will provide this information for all E ports, and F ports logged into a switch?

    A. porterrshow
    B. portstats64show
    C. datatypeshow
    D. errdump 
    A
  175. You experience congestion problems in your Brocade SAN running Fabric OS v7.0.

    Which command would you use to determine the problem?

    A. fabricshow
    B. switchshow
    C. portlogdump
    D. bottleneckmon 
    D
  176. A customer is running into intermittent problems with their SAN. In an effort to diagnose their
    problem, they decide to periodically capture support save information for all the switches in their
    fabric.
     Which two statements regarding Brocade Network Advisor's ability to do this are true? (Choose
    two.)

    A. Brocade Network Advisor has the ability to capture supportsaves for up to four switches in a
    fabric.
    B. Brocade Network Advisor has the ability to capture supportsaves for all switches in a fabric.
    C. Brocade Network Advisor can be setup to automatically capture supportsaves on a daily basis
    for up to four switches.

    D. Brocade Network Advisor can be setup to automatically capture supportsaves on a daily basis
    for all switches in a fabric. 
    BD
  177. A customer is troubleshooting a SAN in which they have large numbers of FC sequences being
    aborted. They have cleared out their port statistics and just hours later noticed large numbers of
    frames on a particular port indicating CRC errors with good end of frames (crc g_eof).

    Which action should the customer take?

    A. Investigate the name service for devices showing CRC errors.
    B. Turn off EOF delimiter verification on the link in question.
    C. Turn off CRC verification on the link in question.
    D. Verify the SFP and cable associated with the link in question. 
    D
  178. You believe you have a physical problem with an ISL in your Brocade SAN running Fabric OS
    v7.0.

    What would you run to troubleshoot the problem?
    A. Configure the ISL to be a D_Port then test the ISL.
    B. Configure the ISL to be an E_Port then test the ISL.
    C. Configure auto negotiate to "off", hard set the speed, then test the ISL.
    D. Configure the ISL to be a G_Port then test the ISL. 
    A
  179. A customer has connected two Brocade 6510s together and the link has come up at 8 Gbps. The
    customer cannot determine why the link is not coming up at 16 Gbps.

    What are three possible reasons why the link is coming up at 8 Gbps? (Choose three.)

    A. The cable used is an OM2 cable.
    B. The cable used is an OM3 cable.
    C. The port speed on one or both of the two ports is fixed at 8 Gbps.
    D. One or both of the two SFPs is a Brocade-branded 8 Gbps SFP.
    E. The portcfgoctetspeedcombo on one of the two switches is set for speeds 2/4/8/10 Gbps. 
    CDE
  180. A customer is having a Brocade 825 HBA fabric login problem. They are asked to obtain an HBA
    supportsave.

    Which three tools can be used? (Choose three.)

    A. Brocade Network Advisor
    B. Brocade Command Utility (BCU)
    C. Host Connectivity Manager (HCM)
    D. Web Tools
    E. Fabric OS CLI 
    ABC
  181. You were asked to provide a trace dump on a Brocade Director.
    Which command will enable and automate the upload of this data?

    A. supportftp
    B. supportshow
    C. supportsave
    D. supportffdc 
    A
  182. You run spinfab to test fabric performance.
    Which statement is true?

    A. It is an offline diagnostics command used to verify the ISL links between switches at the
    minimum speed.
    B. It is an online diagnostics command used to verify the ISL links between switches at the
    maximum speed.

    C. It is an online diagnostics command used to verify the ISL links between switches at the
    minimum speed.
    D. It is an offline diagnostics command used to verify the ISL links between switches at the
    maximum speed. 
    B
  183. You run fcping to identify why you cannot access your newly installed storage.
    Which two functions does the command provide? (Choose two.)
    A. Identifies congestion between source and destination port.
    B. Validates FC link connectivity between the source and the destination port.
    C. Obtains bandwidth information.
    D. Performs a zoning check of the specified source and the destination port. 
    BD
  184. You run nszonemember to validate if all the tape drives are zoned with a specific server port.
    Which statement about the command is true?

    A. It displays local NS information about all devices connected to a switch.
    B. It displays information on all online devices zoned with the specific device.
    C. It displays information on all devices zoned with the specific device.
    D. It displays remote NS information about the online devices connected to a switch 
    B
  185. Your customer complains about various application timeouts on their servers. In the truncated
    output shown in the exhibit, several ports show a high number of errors.

    Which action should be performed first?

    A. Replace the cables on all ports which show CRC errors.
    B. Replace the SFPs on all ports which show CRC errors.
    C. Clear the counters and wait for period of time then gather new output.
    D. Clean all cables and patch panel connections with error counts. 
    C
  186. At your customer's site, all of the servers and storage connected to sw1 lost their connection
    during the night.

    Referring to the exhibit, which statement about the hashow output is true?

    A. The Brocade Director is on-line and the most recent CP failover was non-disruptive.
    B. The Brocade Director is currently completing a non-disruptive failover.
    C. The Brocade Director is on-line and the most recent CP failover was disruptive.
    D. The Brocade Director is currently recovering from a disruptive failover. 
    C
  187. You were asked to use porttest on some of your storage ports due to possible physical layer
    issues.

    Which two functions does this command provide? (Choose two.)

    A. Detects congestion on this port.
    B. Isolates problems in a single replaceable element.
    C. Measures the throughput of the port.
    D. Verifies the persistence of failures detected earlier. 
    BD
  188. You have issued the psshow command on a switch with multiple power supplies installed. One of
    the power supplies indicates a faulty status.

    Which two statements are correct? (Choose two.)

    A. The power switch is turned off.
    B. The power supply is not installed.
    C. The power cord is plugged into a dead receptacle.
    D. The input voltage is incorrect. 
    AC
  189. You added a new server to your SAN, but it cannot connect to its storage.
    What are two possible actions to troubleshoot the problem? (Choose two.)

    A. Use nszonemember to verify that the right storage is in the server's zone.
    B. Use zoneshow to verify that the right storage is in the server's zone.
    C. Use nsshow to verify that the right storage is in the server's zone.
    D. Use nsallshow to verify that the right storage is in the server's zone. 
    AB
  190. You have been asked to troubleshoot a segmented fabric problem between two Brocade 6510
    switches.

    Which two could be used to troubleshoot this problem? (Choose two.)

    A. CLI
    B. Fabric Watch
    C. Host Connectivity Manager
    D. Web Tools 
    AD
  191. You need to collect supportsave information from a Brocade 6510. The 6510 does not have an
    active management connection due to a network outage.
    What would you use to gather the supportsave data required without an active management
    connection?

    A. Brocade Network Advisor
    B. in-band management
    C. USB stick
    D. SAN Health 
    C
  192. You have been asked to troubleshoot a segmented fabric problem between two Brocade 6510
    switches.

    Which two parameter settings could be the cause of this problem? (Choose two.)

    A. identical Domain IDs
    B. different Domain IDs
    C. different RA_TOVs
    D. identical RA_TOVs 
    AC
  193. Which statement is correct about how FSPF selects the preferred device path through the fabric?

    A. FSPF uses the lowest link cost for an ISL or trunk connected to the principal switch in a multi-
    hop fabric.
    B. FSPF uses the lowest congested ISL when the device initially logs into the fabric.
    C. FSPF uses the lowest total link cost for multiple paths between end devices.

    D. FSPF uses the lowest total distance of all links in the path for end devices.
    C

What would you like to do?

Home > Flashcards > Print Preview