BOMBER BLEED AIR DISTRIBUTION

Card Set Information

Author:
carLORENZ0
ID:
255370
Filename:
BOMBER BLEED AIR DISTRIBUTION
Updated:
2014-01-06 14:30:28
Tags:
aslkdjfh
Folders:
alskdjhf
Description:
;asdjf
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user carLORENZ0 on FreezingBlue Flashcards. What would you like to do?


  1. provides hot, pressurized air for several key features for the aircraft.
    BLEED AIR
  2. Temperature and pressure dependent on
    throttle setting
  3. -is an external source for bleed air. 

    + Ground air cart

    - This is used for engine start
    Used for operational checks and troubleshooting

    +A/C system
    +Bleed Air System
    Dash 60A (-60A)
  4. +One is placed on each strut

    + Strut 2 is primary connection for engine starts and operational checks
    + Struts 1,3, & 4 alternate connection
    Ground Service Receptacle
  5. is in place to insure that air flows in only one direction and prevent reverse airflow.
    Ground Service Receptacle Check Valve
  6. • Strut number 2 (engines 3 and 4)
    -Last stage of compression 16th stage
    -Pressure and temperature depends on the throttle setting
    Internal (Normal) Source of Bleed Air
  7. -Prevents reverse flow
    -One per engine
    Engine Bleed Air Check Valves
  8. What is an Emergency Source of Bleed Air?
    Strut 3 (engine 5 & 6)
  9. • Reduces bleed air temperature
    - Transforms heat from bleed air to ram air
    +Located in strut 2
    - Bleed air SEEKS Ram Air
    Pre-cooler
  10. • Open for engine start
    -Open for operational check of bleed valve
    + Solenoid controlled 28-VDC, air actuated
    * HOT AIR VALVES *
    - Power and air needed to open
    + Failsafe closed
    - Controlled by the manifold valve switch
    Strut Bleed Air Valves 1 & 4
  11. • Located in the left wing manifold

    -Controls flow from strut 2

    +Actuated by 115 vac motor
    -Opens for normal system operation (IN FLT)
    -Opens for engine starts
    -CLOSED for emergencies 
    + Makes sure Strut #3 is closed
    +Controlled by Bleed selector, manifold valve switch, or the cabin pressure master switch
    Body Crossover Manifold Valve
  12. • Actuated by 115 vac motor
    - Normally closed
    + Opened for engine start
    - Opened for EMERGENCY bleed air
    - Closed during Normal Sys. Op. 
    + Controlled by (ALL 4 SW)

    Bleed selector(Emergencies),

    manifold valve switch(Engine Start, Opens Valve),
    or the cabin pressure master switch
    Strut 3
  13. Strictly used for Engine Start & OPS CHECKS.

    + OPEN - ALL VALVES OPEN
    + CLOSE - ALL VALVES CLOSED

    Operates: Strut 1,3,4 & Body Crossover Manifold
    Manifold Valve Switch
  14. • Determines source of bleed air by controlling Strut #3 & body manifold crossover

    Two Position

    Normal:

    -Strut 3 is CLOSED
    -Body crossover manifold valve OPEN

    Emergency:

    -Body crossover manifold valve CLOSED
    -Strut 3 bleed air valve is OPEN
    Bleed Selector Switch
  15. • Used to control A/C system
    Four Position

    Ram
    Off
    7.45 psi (normal)
    4.50 psi (combat)
    Cabin Pressure Master Switch
  16. Monitored to ensure proper operation of the bleed air system

    + Indicated temperature between 20 degrees – 300 degrees Centigrade (-4 to 575 degrees Fahrenheit)

    +Red Lined at 246 degrees centigrade (475 degrees Fahrenheit)
    Manifold Air Temperature Indicator
  17. + Senses bleed air manifold temp
    -Located in the engine bleed air manifold
    -Connected to the temperature indicator
    + Determines POS. of Temp. Indic.
    Sensing Bulb
  18. -Short sections
    -Corrosion resistant steel
    -Convey hot air
    -Support 

    +Single or double hinged swinging gates
    +Allow for pivoting action of the ducting
    + due to IN FLT AIRFRAME MOVEMENT
    Ducting
  19. +Allows doe thermal expansion

    +Compensates for twisting and bending due to normal expansion
    Bellows
  20. + Gasket used to prevent leaks
    • Used on HOT air ducts ONLY
    - Torque bolt
    *All screws&bolts have torque value *
    Bolted Flange (“bolts forged” HOT )
  21. +Used for COLD air ducts
    - Low pressure ducting
    -Torque T bolt
    + Uses a rubber sleeve
    Channel Band Coupling( “C”  Chilli COLD )
  22. +Used for COLD or HOT ducts
    - Torque T bolt
    V-Band Couplings “V” Varies
  23. -Metal foil type
    -Cut down on heat loss
    -Prevents damage to equipment
    -Aids in preventing burns
    Insulation
  24. HOT AIR = Bad ; COLD AIR = Good
    DURING EMERGENCY.
  25. Distribution: One Source coming in & splits it off.
    MANIFOLD
  26. - Strut #3
    - Engine 5&6
    - B/A temperature increases 
    - * Limited RPM 80%
    Engine Source of Bleed Air
  27. SPRING LOADED CLOSED
    HOT AIR VALVE
  28. SPRING LOADED OPEN
    COLD AIR VALVE

What would you like to do?

Home > Flashcards > Print Preview