carpentry 1- stationary power tools

Card Set Information

carpentry 1- stationary power tools
2014-03-23 14:04:39
carpentry 1- stationary power tools
Show Answers:

  1. the threaded shaft/spindle on the table saw that supports the saw blade is called a/an?
  2. what are the 4 basic accessories that are commonly used with a table saw?
    • 1.blade gaurd
    • 2.splitter/antikickback fingers
    • fence
    • 4.mitre gauge
  3. what should be used while cutting on the table saw when the distance between the saw blade and the fence is less than 100mm 4"?
    push stick
  4. which basic accessory fits into the slots machined into the table saw table running parallel to the saw blade?
    mitre gauge
  5. radial arm saws are particularly good for what type of cutting?
    fast accurate cross cutting
  6. what are the 3 basic design types of a radial arm saws?
    • 1.single arm
    • 2.double arm
    • 3.sliding overarm
  7. how do you set up a slightly warped material so that it is safe to cut on the radial arm saw?
    so that it touches the table at exactly where the blade cuts
  8. what are the names of the 2 set ups for ripping using a radial arm saw?
    • 1. in rip
    • 2. out rip
  9. when ripping with the radial saw, it is very important that the stock be fed against the blades rotation and that what 2 things are in place and properly adjusted?
    • 1.blade guard
    • 2.anti kickback fingers
  10. what measurement on a band saw determines the maximum width of material that can be cut?
    the throat measurement which is the difference between the blade and the machines vertical support
  11. keeping the blade running in the centre of the bad saw's wheels is accomplished by adjusting what?
    blade tracking the blade is centred when it rides in the centre of the upper and lower wheels
  12. what are 2 reasons for choosing a band saw to resaw material?
    • 1. the capacity to cut thicker material without the risk of kickback
    • 2. by using fence and a wider blade you can accurately cut thinner strips
  13. the size of a jointer is determined by the length of the _____.
  14. which part of a jointer is raised up and down to regulate the depth of cut?
    infeed (front) table
  15. besides producing flat surfaces and square edges, give 3 examples of other operations that can be performed on the jointer.
    • 1. rabbet
    • 2. tapers
    • 3. bevels
  16. what shape will the resulting cut be if the outfeed table on the jointer is set higher than  the knives?
  17. if the thickness planers are only good for one operation, what is it?
    to machine the wood to a smooth and uniform or parallel thickness
  18. what must your material have before you can plane it, and which machine should you use to prepare your material for the planer?
    one surface must be machined flat and true on a jointer first
  19. how do you determine the shortest length of material that can be planed on a specific planer?
    the distance between the infeed and outfeed rollers so that the leading edge would be gripped by the outfeed rollers before the trailing edge is let go by the infeed
  20. what is the minimum size of drill press capable of boring a hole through the centre of a piece of material 380mm 15" in diameter?
    a 15" drill press are measured to the centre of the chuck to the column so the drill press is only capable of drilling a whole in the centre of material 7 1/2" from the column
  21. explain how to change speeds on a drill press equipped with step pulleys.
    while stopped the tension is released on the v belt than it is moved manually to different positions on the pulley
  22. why would you clamp the long end of material to the left of you when using the drill press?
    put it to the left so if it comes loose it is taken into the column rather than the operator
  23. what hold the abrasive paper on a disc sander?
    it is glued to the metal disc surface
  24. which part of the sanding disk is used for sanding?
    only the part rotating down
  25. what is the benefit of cleaning the abrasive belts and discs on your sanding machine?
    the lifespan of the belt or disc can  be greatly increased
  26. the tool rest on the grinder should be positioned no further than 3mm 1/8" from___
    the abrasives wheels edge.
  27. why is overheating the edge of a cutting tool while grinding a problem?
    because if it is over heated it destroys the temper