arrl day 7.txt

Card Set Information

Author:
mwinstom
ID:
269585
Filename:
arrl day 7.txt
Updated:
2014-04-07 11:17:24
Tags:
arrl
Folders:
arrl
Description:
arrl
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user mwinstom on FreezingBlue Flashcards. What would you like to do?


  1. Which term describes the rate at which electrical energy is used?
    A. Resistance
    B. Current
    C. Power
    D. Voltage
    C
  2. Electrical power is measured in which of the following units?
    A. Volts
    B. Watts
    C. Ohms
    D. Amperes
    B
  3. What is the formula used to calculate electrical power in a DC circuit?
    A. Power (P) equals voltage (E) multiplied by current (I)
    B. Power (P) equals voltage (E) divided by current (I)
    C. Power (P) equals voltage (E) minus current (I)
    D. Power (P) equals voltage (E) plus current (I)
    A
  4. How much power is being used in a circuit when the applied voltage is 13.8 volts DC and the current is 10 amperes?
    A. 138 watts
    B. 0.7 watts
    C. 23.8 watts
    D. 3.8 watts
    A
  5. How much power is being used in a circuit when the applied voltage is 12 volts DC and the current is 2.5 amperes?
    A. 4.8 watts
    B. 30 watts
    C. 14.5 watts
    D. 0.208 watts
    B
  6. How many amperes are flowing in a circuit when the applied voltage is 12 volts DC and the load is 120 watts?
    A. 0.1 amperes
    B. 10 amperes
    C. 12 amperes
    D. 132 amperes
    B
  7. What formula is used to calculate voltage in a circuit?
    A. Voltage (E) equals current (I) multiplied by resistance (R)
    B. Voltage (E) equals current (I) divided by resistance (R)
    C. Voltage (E) equals current (I) added to resistance (R)
    D. Voltage (E) equals current (I) minus resistance (R)
    A
  8. What is the voltage across a 2-ohm resistor if a current of 0.5 amperes flows through it?
    A. 1 volt
    B. 0.25 volts
    C. 2.5 volts
    D. 1.5 volts
    A
  9. What is the voltage across a 10-ohm resistor if a current of 1 ampere flows through it?
    A. 1 volt
    B. 10 volts
    C. 11 volts
    D. 9 volts
    B
  10. What is the voltage across a 10-ohm resistor if a current of 2 amperes flows through it?
    A. 8 volts
    B. 0.2 volts
    C. 12 volts
    D. 20 volts
    D
  11. What formula is used to calculate current in a circuit?
    A. Current (I) equals voltage (E) multiplied by resistance (R)
    B. Current (I) equals voltage (E) divided by resistance (R)
    C. Current (I) equals voltage (E) added to resistance (R)
    D. Current (I) equals voltage (E) minus resistance (R)
    B
  12. What is the current flowing through a 24-ohm resistor connected across 240 volts?
    A. 24,000 amperes
    B. 0.1 amperes
    C. 10 amperes
    D. 216 amperes
    C
  13. What is the current flowing through a 100-ohm resistor connected across 200 volts?
    A. 20,000 amperes
    B. 0.5 amperes
    C. 2 amperes
    D. 100 amperes
    C
  14. What is the current flow in a circuit with an applied voltage of 120 volts and a resistance of 80 ohms?
    A. 9600 amperes
    B. 200 amperes
    C. 0.667 amperes
    D. 1.5 amperes
    D
  15. What formula is used to calculate resistance in a circuit?
    A. Resistance (R) equals voltage (E) multiplied by current (I)
    B. Resistance (R) equals voltage (E) divided by current (I)
    C. Resistance (R) equals voltage (E) added to current (I)
    D. Resistance (R) equals voltage (E) minus current (I)
    B
  16. What is the resistance of a circuit in which a current of 3 amperes flows through a resistor connected to 90 volts?
    A. 3 ohms
    B. 30 ohms
    C. 93 ohms
    D. 270 ohms
    B
  17. What is the resistance in a circuit for which the applied voltage is 12 volts and the current flow is 1.5 amperes?
    A. 18 ohms
    B. 0.125 ohms
    C. 8 ohms
    D. 13.5 ohms
    C
  18. What is the resistance of a circuit that draws 4 amperes from a 12-volt source?
    A. 3 ohms
    B. 16 ohms
    C. 48 ohms
    D. 8 Ohms
    A
  19. What is the name for standardized representations of components in an electrical wiring diagram?
    A. Electrical depictions
    B. Grey sketch
    C. Schematic symbols
    D. Component callouts
    C
  20. What do the symbols on an electrical circuit schematic diagram represent?
    A. Electrical components
    B. Logic states
    C. Digital codes
    D. Traffic nodes
    A
  21. Which of the following is accurately represented in electrical circuit schematic diagrams?
    A. Wire lengths
    B. Physical appearance of components
    C. The way components are interconnected
    D. All of these choices are correct
    C

  22.  A. Connector
    B. Meter
    C. Variable capacitor
    D. Variable inductor
    D


  23.  A. Antenna
    B. Transmitter
    C. Dummy load
    D. Ground
    A
  24. Which of the following is used together with an inductor to make a tuned circuit?
    A. Resistor
    B. Zener diode
    C. Potentiometer
    D. Capacitor
    D
  25.  
    A. Resistor
    B. Transistor
    C. Battery
    D. Connector
    A

  26. A. Resistor
    B. Transistor
    C. Indicator lamp
    D. Connector
    B
  27. What is the function
    A. Give off light when current flows through it
    B. Supply electrical energy
    C. Control the flow of current
    D. Convert electrical energy into radio waves
    C

  28. A. Resistor
    B. Transistor
    C. Lamp
    D. Ground symbol
    C
  29.  
    A. Resistor
    B. Transistor
    C. Battery
    D. Ground symbol
    C
  30. What type of switch ?
    A. Single-pole single-throw
    B. Single-pole double-throw
    C. Double-pole single-throw
    D. Double-pole double-throw
    A
  31. What is the component
    A. Variable inductor
    B. Double-pole switch
    C. Potentiometer
    D. Transformer
    D
  32. What is component ?
    A. Resistor
    B. Capacitor
    C. Regulator IC
    D. Transistor
    B
  33. What is component ?
    A. Resistor
    B. Inductor
    C. Regulator IC
    D. Light emitting diode
    D
  34. What is component ?
    A. Variable capacitor
    B. Variable inductor
    C. Variable resistor
    D. Variable transformer
    C
  35. Which of the following can be used to display signal strength on a numeric scale?
    A. Potentiometer
    B. Transistor
    C. Meter
    D. Relay
    C
  36. What best describes a relay?
    A. A switch controlled by an electromagnet
    B. A current controlled amplifier
    C. An optical sensor
    D. A pass transistor
    A
  37. What is the approximate amount of change, measured in decibels (dB), of a power increase from 5 watts to 10 watts?
    A. 2 dB
    B. 3 dB
    C. 5 dB
    D. 10 dB
    B
  38. What is the approximate amount of change, measured in decibels (dB), of a power decrease from 12 watts to 3 watts?
    A. 1 dB
    B. 3 dB
    C. 6 dB
    D. 9 dB
    C
  39. What is the approximate amount of change, measured in decibels (dB), of a power increase from 20 watts to 200 watts?
    A. 10 dB
    B. 12 dB
    C. 18 dB
    D. 28 dB
    A
  40. What type of circuit controls the amount of voltage from a power supply?
    A. Regulator
    B. Oscillator
    C. Filter
    D. Phase inverter
    A
  41. What component is commonly used to change 120V AC house current to a lower AC voltage for other uses?
    A. Variable capacitor
    B. Transformer
    C. Transistor
    D. Diode
    B
  42. What is the name of a device that combines several semiconductors and other components into one package?
    A. Transducer
    B. Multi-pole relay
    C. Integrated circuit
    D. Transformer
    C
  43. What does the abbreviation "LED" stand for?
    A. Low Emission Diode
    B. Light Emitting Diode
    C. Liquid Emission Detector
    D. Long Echo Delay
    B
  44. Which of the following is commonly used as a visual indicator?
    A. LED
    B. FET
    C. Zener diode
    D. Bipolar transistor
    A
  45. What is another way to specify a radio signal frequency of 1,500,000 hertz?
    A. 1500 kHz
    B. 1500 MHz
    C. 15 GHz
    D. 150 kHz
    A
  46. How many volts are equal to one kilovolt?
    A. One one-thousandth of a volt
    B. One hundred volts
    C. One thousand volts
    D. One million volts
    C
  47. If an ammeter calibrated in amperes is used to measure a 3000-milliampere current, what reading would it show?
    A. 0.003 amperes
    B. 0.3 amperes
    C. 3 amperes
    D. 3,000,000 amperes
    C
  48. Which of the following is equivalent to 500 milliwatts?
    A. 0.02 watts
    B. 0.5 watts
    C. 5 watts
    D. 50 watts
    B
  49. How many milliamperes is 1.5 amperes?
    A. 15 milliamperes
    B. 150 milliamperes
    C. 1,500 milliamperes
    D. 15,000 milliamperes
    C
  50. How many microfarads are 1,000,000 picofarads?
    A. 0.001 microfarads
    B. 1 microfarad
    C. 1000 microfarads
    D. 1,000,000,000 microfarads
    B
  51. How many volts are equal to one microvolt?
    A. One one-millionth of a volt
    B. One million volts
    C. One thousand kilovolts
    D. One one-thousandth of a volt
    A
  52. Which of the following types of solder is best for radio and electronic use?
    A. Acid-core solder
    B. Silver solder
    C. Rosin-core solder
    D. Aluminum solder
    C
  53. What is the characteristic appearance of a "cold" solder joint?
    A. Dark black spots
    B. A bright or shiny surface
    C. A grainy or dull surface
    D. A greenish tint
    C
  54. Which of the following measurements are commonly made using a multimeter?
    A. SWR and RF power
    B. Signal strength and noise
    C. Impedance and reactance
    D. Voltage and resistance
    D
  55. Which of the following precautions should be taken when measuring circuit resistance with an ohmmeter?
    A. Ensure that the applied voltages are correct
    B. Ensure that the circuit is not powered
    C. Ensure that the circuit is grounded
    D. Ensure that the circuit is operating at the correct frequency
    B
  56. Which of the following might damage a multimeter?
    A. Measuring a voltage too small for the chosen scale
    B. Leaving the meter in the milliamps position overnight
    C. Attempting to measure voltage when using the resistance setting
    D. Not allowing it to warm up properly
    C
  57. What is probably happening when an ohmmeter, connected across a circuit, initially indicates a low resistance and then shows increasing resistance with time?
    A. The ohmmeter is defective
    B. The circuit contains a large capacitor
    C. The circuit contains a large inductor
    D. The circuit is a relaxation oscillator
    B

What would you like to do?

Home > Flashcards > Print Preview