Tool 4 Tool 24

Card Set Information

Author:
csantf100
ID:
275754
Filename:
Tool 4 Tool 24
Updated:
2014-06-01 16:56:42
Tags:
Generators Lights Chainsaw Honda
Folders:
Study Guide Week 10
Description:
Study Guide Week 10 Chain Saw Operations Honda Generator
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user csantf100 on FreezingBlue Flashcards. What would you like to do?


  1. Portable lights by the Dept. utilize?
    500 watt Lamps
  2. If lights fail to illuminate when power is applied, what should be done?
    • check bulb for proper connection
    • replace with new bulb
    • send entire light to TECH SERVICEs
  3. All portable generators have what kind of engines?
    4 cycle, no mixing of gasoline
  4. If a portable generator is used to power an exhaust fan, the ideal length of the electrical cord should be??
    50 feet or less
  5. Is distance a problem when powering small tools and lights??
    NO
  6. Always ensure that engine oil is at the correct level before starting.

    T or F
    True
  7. What is the ONLY maintenance required on lights??
    BULB REPLACEMENT
  8. How do we check portable generators?
    • Operate portable generators weekly for 15 minutes
    • during this time, operate all lights for 5 minutes
  9. When should the oil be changed and by whom?
    after 50 hours by TECH SERVICES
  10. What companies are equipped with Apparatus mounted Generators?
    ALL LADDER COMPANIES
  11. Apparatus 2001 and newer, what gauge wire?
    10 gauge wire

    NO PROBLEMS powering exhaust fans when the length of the electric cord is greater than 50 ft.
  12. All repairs to onboard generators shall be performed by ??
    FLEET SERVICES
  13. When do we check onboard generators?
    MUD
  14. Waterproof connections are good for use in up to??
    3 feet of water
  15. Honda 1000 Watt Tele -lite has what attached to it?
    500 watt halogen lamp

    approx. running time 4.5 hours
  16. The 2000 watt generator has what attached?
    NOTHING..no light

    4.5 hours running time
  17. NEVER USE contaminated or oil mixed fuel in Honda generator.

    T or F
    True
  18. Operations requiring maximum output of HONDA GENERATOR, should be limited to ??
    30 minutes
  19. For repairs, send Honda Generator to??
    TECH SERVICES
  20. When not in use, the fuel tank vent levers and engine switch can be left in the ON position, so the generator is ready to go.

    T or F
    FALSE

    in the OFF POSITION
  21. When can the chain saw be used for ventilation or overhauling of structural fires?
    PIER fire operations
  22. While operating chain saw, OPERATOR and CONTROL PERSON shall wear (NFPA compliant)?
    • long sleeve work duty shirt or bunker coat
    • helmet
    • eye protection
    • saw protected gloves
    • bunker boots
    • saw protected chaps
  23. Warm up chain saw prior to any cutting.

    T or F
    True
  24. What is the proper 'HOLD" of the chainsaw ?
    • always firmly with both hands while engine is running
    • left hand on the front handlebar
    • right hand on the rear handle
    • entire body is to the left of the cutting line
  25. If need be, attempt to cut above chest height.

    T or F
    FALSE

    do not attempt cutting above chest height
  26. When operating on slopes stand on which side?
    the UPHILL SIDE
  27. Hold saw near log and throttle up to FULL SPEED just before allowing chain to touch wood.

    T or F
    TRUE
  28. Always start a cut with the chain rotating at full speed and the bumper spike in contact with the wood.

    T or F
    TRUE
  29. Cutting downward you may experience a _____ reaction?
    PULLING

    chain on bottom
  30. Cutting Upward?
    PUSHING

    chain on top
  31. Control and saw operator will don eye and HEARING protection

    T or F
    TRUE
  32. Circle of Danger for Chain Saw Ops?
    10 foot radius
  33. Who is allowed in this circle of danger?
    saw operator and control person


    if possible OFFICER is positioned as to permit visual contact with the control person
  34. Control member should be positioned in what way?
    • PERMIT EASY VISUAL CONTACT WITH SAW OPERATOR
    • maintain SAFE DISTANCE FROM SAW
    • do not remove cutting debris while operator is cutting
  35. If control member approaches immediate cutting area, what must the operator do??
    apply chain brake and signal control member to approach

    when possible, control member should maintain visual contact with officer
  36. HEARING protection must be worn during operational and training sessions.

    T or F
    TRUE
  37. DEBRIS must not be removed, until who says so??
    SAW OPERATOR
  38. Refuel saw where?
    outside circle of danger
  39. To reduce exposure to high noise levels and prevent fatigue, what must Officer do?
    rotate personnell
  40. Can we attempt to cut an object that has fallen against a structure and is now supported by it?
    NO
  41. Trees are poor conductors of electricity.

    T or F
    FALSE

    trees are GOOD CONDUCTORS OF ELECTRICITY
  42. To avoid kickbacks, never make what kind of cuts?
    • Plunge cuts with tip of bladeĀ 
    • never use tip of the saw blade for cutting
  43. When limbing, do we start on lower limbs?
    NO, LEAVE LOWER LIMBS

    it is not necessary to run saw at full throttle
  44. Chain saw shall NOT be operated from a ladder.

    T or F
    TRUE
  45. Can Chaps be work over shorts?
    NO.

    CHAPS may be worn over LONG PANTS or BUNKER PANTS
  46. Bunker coat, bunker pants, and firefighting gloves are not saw protected and will not prevent the chain saw blade from inflicting sever injury.

    T or F
    TRUE
  47. If chain continues to spin at idle, place saw..?
    OOS

What would you like to do?

Home > Flashcards > Print Preview