Pipefitting Hand tools

Card Set Information

Author:
JOMC0092800
ID:
304091
Filename:
Pipefitting Hand tools
Updated:
2015-06-16 01:15:30
Tags:
Pipefitting John
Folders:
Pipefitting
Description:
Pipefitting Level 1 Edition 3 Module 3
Show Answers:

Home > Flashcards > Print Preview

The flashcards below were created by user JOMC0092800 on FreezingBlue Flashcards. What would you like to do?


  1. A screwdriver may be used as a pry bar as long as it is sturdy enough for the application. 

    a) True
    b) False
    b) False
  2. A three-legged pipe jack stand can be used for pipe up to _____ inches in diameter. 

    A) 2
    B) 6
    C) 8
    D) 4
    B) 6
    (this multiple choice question has been scrambled)
  3. The height of a three legged jack stand is typically adjusted by placing it on blocks.

    a) True 
    b) False
    b) False
  4. The type of wrench that would be used on a chrome plated pipe is the ______ wrench.

    A) strap
    B) chain
    C) Crescent
    D) offset pipe
    A) strap
    (this multiple choice question has been scrambled)


  5. The tool shown in Figure 1 is a(n)________. 

    A) compound leverage pipe wrench
    B) strap wrench
    C) pipe vise
    D) offset pipe wrench
    A) compound leverage pipe wrench
    (this multiple choice question has been scrambled)
  6. The term plumb relates to _______.

    A) horizontal alignment
    B) vertical alignment
    C) pipe height
    D) pipe location
    B) vertical alignment
    (this multiple choice question has been scrambled)
  7. A torpedo level is a good choice when accuracy is important

    a) True
    b) False
    b) False
  8. A framing level can be used to measure ______. 

    A) plumb or level 
    B) plumb only
    C) level only
    D) boobies :)
    A) plumb or level
    (this multiple choice question has been scrambled)
  9. Which of the following is a task that cannot be performed with a framing square?

    A) Aligning two sections of pipe
    B) Finding the center line of a pipe
    C) measuring the diameter of a pipe
    D) Checking squareness of a pipe end
    C) measuring the diameter of a pipe
    (this multiple choice question has been scrambled)


  10. Figure 2 shows a tool used to _____.

    A) measure the outside diameter of a pipe
    B) tap a hole in a pipe 
    C) locate the center of a pipe
    D) bevel a pipe
    C) locate the center of a pipe
    (this multiple choice question has been scrambled)
  11. A t-joint welding clamp is used to hold a pipe section perpendicular to another pipe.

    a) True 
    b) False
    a) True
  12. A Hi-Lo gauge is used to ______.

    A) measure the inside diameter of a pipe
    B) check pipe joint misalignment
    C) check pressure in a piping system
    D) check for weld defects
    B) check pipe joint misalignment
    (this multiple choice question has been scrambled)
  13. A wraparound is used to ______.

    A) draw a straight line around a pipe 
    B) align pipe joints for welding
    C) secure a pipe to a jack stand
    D) measure the inside diameter of a pipe
    A) draw a straight line around a pipe
    (this multiple choice question has been scrambled)
  14. Drift pins are used to _____.

    A) align bolt holes on pipe flanges
    B) keep pipe joints from moving while they are being welded
    C) secure pipes in jack stands
    D) check alignment of a pipe joint
    A) align bolt holes on pipe flanges
    (this multiple choice question has been scrambled)
  15. A hacksaw blade used to cut copper tubing should have ______ teeth per inch.

    A) 32
    B) 18
    C) 14
    D) 24
    D) 24
    (this multiple choice question has been scrambled)


  16. The tool shown in Figure 3 is used to cut _____.

    A) thin-wall copper tubing
    B) cast iron soil pipe
    C) carbon steel pipe
    D) cement pipe
    C) carbon steel pipe
    (this multiple choice question has been scrambled)


  17. The tool shown in Figure 4 is used to _____.

    A) thread pipe 
    B) bevel pipe ends
    C) ream pipe
    D) position pipe for welding
    A) thread pipe
    (this multiple choice question has been scrambled)
  18. Threading is complete when ____ full thread (s) extend(s) beyond the back edge of the die.

    A) 4
    B) 3
    C) 1
    D) 2
    C) 1
    (this multiple choice question has been scrambled)
  19. Pipe taps are used to _____.

    A) remove broken plugs and fittings
    B) cut female threads of a pipe
    C) drill holes in pipe
    D) cut male threads of a pipe
    B) cut female threads of a pipe
    (this multiple choice question has been scrambled)
  20. Lever compression tube benders can be used to bend pipe up to 1 inch in diameter.

    a) True
    b) False
    b) False
  21. What is Burr?
    Burr is a sharp, tagged edge of metal usually caused by cutting pipe.
  22. What is Conduit?
    Conduit is a round raceway, similar to pipe, that contains conductors.
  23. What is die?
    Die is a tool used to make male threads on a pipe or bolt.
  24. What is female threads?
    Female threads are threads on the inside of a fitting
  25. What is Flare?
    Flare is a pipe end that has been forced open to make a joint with a fitting
  26. What is male threads?
    Male threads are threads on the outside of a pipe.
  27. What is the outside diameter?
    The outside diameter is a measurement of the outside width of a pipe.
  28. What is Pipe-fitting?
    Pipe-fitting is a unit attached to a pipe and used to change the direction of fluid flow, connect a branch line to a main line, close off the end of a line, or join two pipes of the same size or of different sizes.
  29. What is a Ratchet?
    A ratchet is a device that allows a tool to rotate in only one direction
  30. What is tack welds?
    Tack welds are short welds used to hold parts in place until the final weld is made.
  31. What is a thread gauge? What else can it be called?
    A tool used to determine how many threads per inch are cut in a tap, die, bolt, nut or pipe. Also called a pitch gauge.

What would you like to do?

Home > Flashcards > Print Preview