Engine Fire at Take-off Procedure

Home > Preview

The flashcards below were created by user allanah on FreezingBlue Flashcards.


  1. Engine Fire at Take-off Procedure
    • Announce “V1”
    • Announce “Rotate”
    • Check positive rate of climb on
    • IVSI and altimeter.
    • Announce “Positive climb”

    • Verify positive rate of climb on IVSI
    • and altimeter.
    • Announce “Gear up”

    • Select gear up.
    • Engage yaw damper.

    • FIRE 1(2)
    • ENG [x] FIRE on EWD and Fire Handle Illuminated

    Announce “Engine fire”

    • Announce “Confirmed”
    • Cancel Master Warning.
    • Broadcast “Mayday, mayday, mayday, Mount Cook [xx], engine fire, standby”
    • Announce “Gear is up”
    • Announce “Acceleration altitude”

    • Announce “Set speed manual,
    • VFTO”

    • On the ICP:
    • SPD TGT ....................... SET MAN
    • SPD TGT (blue bug) ......SET VFTO
    • Announce “VFTO [xxx] blue”

    • Announce “Checked”
    • Check PL 1 + 2 in the notch.
    • Announce “Power levers notch”
    • Announce “Set MCT”

    • PWR MGT...................... SET MCT
    • Announce “MCT set”

    Announce “VFTO”

    • In normal conditions, announce
    • “Normal conditions, set flaps
    • zero”
    • In icing conditions, announce
    • “Icing conditions, flaps fifteen
    • remain”

    • Flaps .........................SET AS REQ
    • In normal conditions, announce “Flaps zero”
    • In icing conditions, announce “Flaps fifteen”

    Announce “Engine fire at takeoff memory items”

    • Identify the affected engine.
    • Announce “Engine [x] fire”

    Announce “Confirmed”

    • Touch PL [x].
    • Announce “Power lever [x], flight idle”

    • Check correct PL.
    • Announce “Confirmed”

    • PL [x].................... RETARD TO FI
    • Touch CL [x].
    • Announce “Condition lever [x], feather then fuel shut-off”

    • Check correct CL.
    • Announce “Confirmed”

    • CL [x]................. RETARD TO FTR
    • After 1 second:
    • CL [x]...........RETARD TO FUEL SO

    • Touch Fire Handle [x].
    • Announce “Fire handle [x], pull”

    • Check correct Fire Handle.
    • Announce “Confirmed”

    • Fire Handle [x]..................... PULL
    • Check the timer has started on the EWD.
    • Point to Agent 1 P/B.
    • Announce “Ten seconds, agent one discharge”

    • Check Agent 1.
    • Announce “Confirmed”

    • Agent 1 P/B .......................PRESS
    • Check discharge light illuminates.
    • Point to Agent 2 P/B.
    • Announce “Thirty seconds, fire continues, agent two discharge”

    • Check Agent 2.
    • Announce “Confirmed”

    • Agent 2 P/B....................... PRESS
    • Check discharge light illuminates.
    • If the red warnings on the EWD and the fire handle extinguish, the PM will announce “Fire is out”

    Announce “Bleed live engine, off if necessary”

    • After considering performance and engine parameters decide on or off.
    • Announce “On or Off”

    • BLEED live engine ......SET AS REQ
    • Announce “Memory items complete”

    *If the fire has stopped, proceed to the Engine Fire at Take-off checklist.

    Announce “Engine fire at takeoff checklist”

    • Perform the Engine Fire at Take-off checklist.
    • Once the checklist is complete, announce “Engine fire at takeoff checklist complete”

    • With the PM, review:
    • -Aircraft performance and tracking
    • -FWS messages
    • -SD pages
    • -Local alerts
    • Once the review is complete:
    • Announce “Clear the FWS”

    FWS......................................CLR

    Announce “After take-off checklist”

    • Perform the After Take-off
    • checklist.
    • Once the checklist is complete, announce “After take-off checklist complete”

    Announce “Single engine operation checklist”

    • Perform the Single Engine Operating checklist.
    • Once the checklist is complete, announce “Single engine operation checklist complete”

    *Take-off + 10 minutes

    • If MSA has not been reached:
    • Announce “Set drift down speed”

    • On the ICP:
    • SPD TGT ..........SET DRIFT DOWN
    • Announce “Drift Down [xxx] Blue”

    Announce “Checked”
  2. Engine Fire at Take-off normal sequence
    • 1. Memory Items
    • 2. QRH Engine Fire at Take-off Checklist
    • 3. After Take-off Checklist
    • 4. QRH Single Engine Operating Checklist
  3. Single Engine Go-Around/ Missed Approach
    • Announce “Going around”
    • Simultaneously:
    • - Push the PL GA button
    • - Rotate to GA pitch attitude on the FD
    • - Set live engine PL to the RAMP

    On the FMA check GA is displayed.

    Announce “Flaps 15” 

    • Select FLAPS 15.
    • IVSI and altimeter.
    • Announce “Positive climb”

    • Verify positive rate of climb on VSI and altimeter.
    • Announce “Gear up, check power”

    • LDG GEAR .................. SELECT UP
    • Check go-around power achieved.
    • Announce “Power set”

    Follow FD to climb at VGA.

    • If LNAV is engaged to not select heading.
    • Announce “LNAV green”
    • If HDG HOLD is displayed on the FMA, on the FGCP press HDG.
    • On the FMA, check:
    • HDG SEL LO
    • Announce “Heading select LOW green”

    Request LNAV as required.

    • On the FGCP press IAS.
    • On the FMA check:
    • IAS
    • Announce “IAS green”
    • Check IAS target bug (blue) matches VGA.
    • Announce “VGA [xxx] blue”

    • Check missed approach altitude set.
    • Announce “[xxxx] set ALT SEL BLUE”

    • Check missed approach altitude set.
    • Announce “Checked”

    • Check Flaps 15 set.
    • Announce “Flaps 15”
    • Check landing gear retracted.
    • Announce “Gear is up”
    • Check target go-around torque set.
    • Announce “Power set”
    • Broadcast “Mount Cook [xxxx], going around”

    Announce “Acceleration altitude”

    Announce “Select ALT”

    • On the FGCP, press ALT.
    • When ALT on the FMA, announce “ALT green”

    • Announce “Checked”
    • Announce “Set VFGA”

    • On the ICP:
    • SPD TGT (blue bug) ......SET VFGA
    • Announce “VFGA [xxxx] Blue”

    Announce “Checked”

    Announce “VFGA”

    • Check PL 1 + 2 in the notch.
    • Announce “Power levers notch”
    • Announce “Select MCT”

    • PWR MGT.................SELECT MCT
    • Announce “MCT set”

    Announce “Select IAS”

    • On the FGCP, press IAS.
    • When IAS on the FMA, announce “IAS green”

    • Announce “Checked”
    • In normal conditions, announce “Normal conditions, set flaps zero”
    • In icing conditions, announce “Icing conditions, flaps fifteen remain”

    • Flaps.........................SET AS REQ
    • In normal conditions, announce “Flaps zero”
    • In icing conditions, announce “Flaps fifteen”

    Announce “After Take-off Checklist”

    Perform the After Take-off Checklist

Card Set Information

Author:
allanah
ID:
326622
Filename:
Engine Fire at Take-off Procedure
Updated:
2016-12-10 01:27:56
Tags:
EFATO
Folders:

Description:
Engine Fire at Take-off Procedure
Show Answers:

Home > Flashcards > Print Preview