API 510 Data Sheets Misc - CLOSED BOOK QUESTIONS

Home > Preview

The flashcards below were created by user Gibby on FreezingBlue Flashcards.


  1. Define repair (key words)
    Restore and suitable

    Reference API 510: 3.1.61
  2. Define alteration (key words)
    Physical change

    Reference API 510: 3.1.1
  3. Define RBIs two primary factors
    Probability and consequence

    Reference API 510: 5.2.1
  4. Where is the MAWP located at on a vessel?
    The top.

    Reference API 510: 3.1.44
  5. What is an imperfection that exceeds the acceptance criteria?
    A defect.

    Reference API 510: 3.1.15
  6. What is a flaw that may or may  not exceed the acceptance criteria?
    An imperfection

    Reference API 510: 3.1.27
  7. Design - What is the joint category of a vessel longitudinal weld?
    A

    Reference VIII: Fig UW-3
  8. Design - What is the joint category of a vessel circumferential weld?
    B

    Reference VIII: Fig UW-3
  9. What is the joint category of a vessel nozzle attachment weld?
    D

    Reference VIII: Fig UW-3
  10. What is the joint category of a vessel flange-to-nozzle attachment weld/shell-to-girth flange attachment weld?
    C

    Reference VIII: Fig UW-3
  11. Design - What are the RT factors representing full RT?
    RT-1 and RT-2

    Reference VIII: UG-116.e.1 and 2
  12. Design - What are the RT factors representing Spot RT?
    RT-3

    Reference VIII: UG-116.e.3
  13. Design - Weld Type - Butt double welded?
    Type 1

    Reference VIII: Figure UW-12
  14. Design - Weld Type - Butt single welded with backing?
    Type 2

    Reference VIII: Figure UW-12
  15. Design - Weld Type - Butt single welded without backing?
    Type 3

    Reference VIII: Figure UW-12
  16. Design - What vessel service always requires full RT?
    Lethal

    Reference VIII: UW-11.a.1
  17. Design - What is the maximum set pressure for a single relief device on a vessel?
    MAWP

    Reference VIII: UG-134.a
  18. Design - What is the marking on the nameplate that indicates the vessel was PWHT'D?
    HT

    Reference VIII: UG-116.f.1
  19. Design - What is the marking on the nameplate that indicates the vessel is in lethal service?
    L

    Reference VIII: UG-116.c
  20. Design  - What is the ASME Sect VIII stamp for routine vessels?
    U

    Reference VIII: UG-116.a.1.a
  21. Design - What is the ASME Sect VIII stamp for miniature vessels?
    UM

    Reference VIII: UG-116.a.1.b
  22. Design - What is the ASME Sect VIII stamp for relief devices?
    UV

    Reference VIII: UG-129.a.7
  23. NDE - What is the number of CMLs required to obtain thickness readings during inspection? (key word)
    Representative

    Reference API 510: 5.6.2.1
  24. NDE - What is the number of nozzles to obtain thickness readings on during inspection? (Key word)
    Representative

    Reference API 510: 5.6.2.1
  25. NDE - What lead letter is used during RT to check for backscatter radiation?
    B

    Reference Sect V: T-223
  26. NDE - What lead letter is used during RT to indicate a film-side IQI?
    F

    Reference Sect V: T277.b
  27. NDE - What hole size must be visible during RT when using a hole-type IQI?
    2T

    Reference Sect V: Table T-276
  28. NDE - What are the type primary gamma-ray RT sources?
    Ir 192 and Co 60.

    Reference API 577: 9.8.4
  29. Relief Valves - How are relief devices to be transported?
    Upright

    Reference API 576: 5.8.4.2
  30. Relief Valves - How are relief device intervals determined? (key word)
    By performance

    Reference API 510: 6.6.3.1
  31. Welding - What are the variables needed on a WPS?
    Essential and Non-essential

    Reference IX: QW200.1.b
  32. Welding - Variables needed on a PQR?
    Essential

    Reference IX: QW200.2.b
  33. Welding - What welding processes are used when substituting preheat or CDW (controlled deposition welding) for a required PWHT? (3)
    SMAW, GMAW, GTAW

    Reference API 510: 8.1.7.4.3.2.1.b and 8.1.7.4.3.3.c
  34. Welding - What is the minimum taper required for shell welds with mismatch?
    3 to 1

    Reference VIII: UW 9.c
  35. Weld Qualification - What is the "all position" test coupon?
    6G

    Reference IX: QW461.9
  36. Weld Qualification - What indications are rejectable in RT when qualifying a welder?
    Cracks, Incomplete penetration, and Lack of fusion

    Reference IX: QW191.1.2.2.a.1
  37. Weld Qualification - Which welding process can a welder NOT be qualified by RT?
    GMAW - SC

    Reference IX: QW-304
  38. Weld Qualification - What is the maximum allowed thickness on a WPS based on the plate thickness (T) of PQR test coupon?
    2T

    Reference IX: Table QW451.1

Card Set Information

Author:
Gibby
ID:
333652
Filename:
API 510 Data Sheets Misc - CLOSED BOOK QUESTIONS
Updated:
2017-08-23 02:09:23
Tags:
API 510
Folders:

Description:
MSTS Misc
Show Answers:

Home > Flashcards > Print Preview