-
What is the major difference between the SAL and RF missiles?
- SAL - laser guided
- RF - radar assisted
-
How will a live missile be coded if there is a M36 training missile loaded on the launcher rail?
NA
-
The fuze contains the ARM/SAFE device that arms the missile when its launch accelleration exceeds _____ g's between ____ to _____ meters in front of the aircraft.
-
When trust exceeds ____ to _____ pounds the missile leaves the rail.
500-600
-
The thrust duration is approxiamately 2 to 3 seconds and the maximum velocity of the missile is ________.
475 mps or Mach 1.4
-
Can the M299 fire all variants of the Hellfire missile?
yes
-
What component contains the Training Missile Emulator (TME) that simulates RF missile training?
Launcher Electronics Assembly
-
What MPD page can you electronically arm the M299 missile launcher?
WPN UTIL LNCHR ARM
-
What are the normal pylon articulation limits when the missiles or rockets are actioned?
+4.9 to -15 degrees
-
What negative factor during target illumination will cause the laser spot to spill over the target?
overspill
-
What are the three LOAL trajectory modes?
-
When the TADS LOS and the seeker LOS differ by more than _____ degrees a BACKSCATTER message will display in the weapons inhibit section of the HAD.
2
-
The safety inhibit backscatter is generally caused by ________, ___________, and ___________.
poor target reflectivity, co-located obscurants, and excessive designation range
-
If the aircraft is 50 to 400 feet above the target you would increase the minimum range for LOAL launch by ________ meters.
500m
-
Your target is 5000 meters away and you need to clear a mask that is 900 feet above the aircraft, what trajectory would you select to engage that target?
LOAL HI
-
For a 5000 meter hellfire engagement the last _____ seconds needs to be steady-on-target time (terminal guidance).
6
-
What determines the SAL LOBL trajectory altitude?
range to target
-
What is the maximum offset limit between the gun target line and the remote designator to the target line?
60 degrees
-
Maximum autonomous designation range is limited by the _____________.
TADS ability to maintain laser spot on target
-
During remote designation, the remote designator should not be within a + _____ degree fan from the gun to target line.
30
-
During rapid fire engagements the maximum separation between targets should not exceed _______ meters, with at least an ________ second separation between missile launches.
-
In the Ripple mode, after the primary channel missile is launched the alternate channel missile may be launched after _____ second separation.
1.5
-
For an autonomous engagement, the aircraft should be oriented _____ to _____ degrees to the side from which the missile is launched.
3-5
-
What are the three RF missile modes?
- standby
- prelaunch
- postlaunch
-
Transfer alignment occurs in the ______ missile mode.
standby (takes 9 to 10 seconds)
-
In the pre-launch mode what are the three methods of target handover data to the RF missile?
-
Doppler beam sharpening (DBS) uses a curved trajectory to induce a relative motion for stationary targets (STI) to enhance the probability of detection and tracking between what ranges?
2.5 - 8 Km
-
At a range of _____ to ______ meters, targets are too close for a LOAL engagement and must be a LOBL engagement or a "NO ACQUIRE" message will be displayed.
.5 - 1 Km (will attempt LOBL 3 times)
-
The 3 RF missile acquisition modes are ____________, ____________, and ____________.
- terminal track acq
- pre-terminal track acq
- moving target acq
-
A SAL missile icon that has not been coded will display _______.
L
-
RF missiles have a _________ instead of a straight line at the seeker.
V
-
An RF missile that has an overtemp condition will display _________.
OT
-
A hangfire will display _______ in the missile icon.
MH
-
If a missile has failed, the icon will display ________.
MF
-
The ALT CHAN button is only selectable after a _________ CHAN has been entered.
PRI
-
The quantity defaults to _________ for both channels if sufficient missiles are available.
3
-
What is the sequence to edit a laser code?
-
What is the tri-service pulse repetition frequency (PRF) code range?
1111-1788
-
The missile MODE selections are _______ in each crewstation.
common
-
In the AUTO power mode, the missiles are powered-up at ________ minute intervals.
10
-
2nd target inhibit selection is used for __________ targets?
FCR truly stationary targets
-
The RF missiles can overheat (OT) if it is radiating (tracking) a target for more than _____ minutes.
3
-
How many missiles will be powered with 6 missiles on board with the AUTO power mode selected?
2
-
What inhibits can be overridden, and how is this accomplished?
performance, 2nd detent
-
Is the message "BACKSCATTER" a safety or performance inhibit?
safety
-
What does the message "ALT LAUNCH" mean?
w/in 2 seconds of rocket launch
-
What is the RF missile radiation hazard area to be avoided?
1m 45 degrees polar from CL
-
How many TME's are on each aircraft?
on in each launcher electronics assembly
-
Tactical missiles will be coded ________ while in the training mode.
NA
-
The TME allows for thermal management of the missiles by allowing for a cumulative time ON of _______ minutes.
30
-
With the TRAIN mode selected and a weapon system is actioned the weapons inhibit field will display ____________.
TRAINING
-
The constraints box will display a _______ centered in the box when the weapon system is actioned in the training mode.
T
|
|