iatii-b

The flashcards below were created by user iamaphoenix on FreezingBlue Flashcards.

  1. Which of the following server types translates NetBIOS names to IP addresses?
    A. WINS
    B. FTP
    C. DNS
    D. DHCP
    A. WINS
    (this multiple choice question has been scrambled)
  2. Which of the following server types performs the same function as the HOSTS file?
    A. DNS
    B. WINS
    C. DHCP
    D. FTP
    A. DNS
    (this multiple choice question has been scrambled)
  3. Which of the following BEST describes RAID 5?
    A. RAID 5 is data striping with a dedicated parity drive.
    B. RAID 5 is data striping across all drives.
    C. RAID 5 is striped sets with parity striped across all drives.
    D. RAID 5 is striped sets with two sets of parity striped across all drives.
    C. RAID 5 is striped sets with parity striped across all drives.
    (this multiple choice question has been scrambled)
  4. Which of the following key sequences will allow a technician to install third party drivers during a Windows installation?
    A. Press F6
    B. Press Alt+F8
    C. Press ESC
    D. Press any key
    A. Press F6
    (this multiple choice question has been scrambled)
  5. Which of the following will attach to an EIDE connector?
    A. ATA-2
    B. SATA
    C. SCSI
    D. SATA-2
    A. ATA-2
    (this multiple choice question has been scrambled)
  6. How many wire pairs are in a standard CAT6 cable?
    A. 8
    B. 4
    C. 6
    D. 3
    B. 4
    (this multiple choice question has been scrambled)
  7. An administrator is configuring one server to monitor hardware level information on a second Windows server. Which of the following should be setup on the Windows server to allow the monitoring server to access this information? (Select TWO).
    A. WMI
    B. RIS
    C. DNS
    D. SNMP
    E. SMTP
    • A. WMI
    • D. SNMP
  8. A company is deploying a new file server to consolidate shares from several legacy servers. Which of the following is the BEST method to ensure that the new file shares are being used?
    A. Setup the new file server and shut down the legacy servers.
    B. Remove all the DNS entries for the legacy servers.
    C. Create a logon script to remap the old file shares to the new file shares.
    D. Go to each users computer, remove all shares and setup the new shares.
    C. Create a logon script to remap the old file shares to the new file shares.
    (this multiple choice question has been scrambled)
  9. Two file servers have run out of local disk space. The internal drives are at capacity and the company has traditionally only used local disks for storage. Which of the following is the MOST cost effective solution to add storage to both servers?
    A. Add a NAS to the environment.
    B. Install fiber cards into the servers and implement a SAN solution.
    C. Install fiber cards into the servers and add direct attached storage.
    D. Attach a USB drive to one of the servers.
    A. Add a NAS to the environment.
    (this multiple choice question has been scrambled)
  10. A company has implemented a wireless network for its employees. Since implementing the new network, individuals have been receiving duplicate IP addresses causing network issues. Which of the following would resolve this issue?
    A. Add another DHCP server.
    B. Add another wireless access point.
    C. Disable the wireless DHCP server.
    D. Change the default gateway of the wireless router.
    C. Disable the wireless DHCP server.
    (this multiple choice question has been scrambled)
  11. A company has several legacy servers that upper management would like to move into a virtual environment. Which of the following is the FIRST step an administrator should take to evaluating whether the servers can be moved into the virtual environment?
    A. Check the HCL on each legacy server.
    B. Run SYSPREP on each legacy server.
    C. Verify that all the latest OS service packs are installed on each server.
    D. Compare the costs of maintenance between the physical and virtual servers.
    A. Check the HCL on each legacy server.
    (this multiple choice question has been scrambled)
  12. Which of the following is MOST useful in HVAC planning? (Select TWO).
    A. Uninterruptible Power Supply (UPS) load
    B. Humidity
    C. Amperage
    D. Voltage
    E. Temperature
    • B. Humidity
    • E. Temperature
  13. B. Multicore
  14. A server is having problems booting into the operating system. Which of the following can provide important information to begin to troubleshoot the cause?
    A. Application logs
    B. POST messages
    C. Firmware updates
    D. System logs
    B. POST messages
    (this multiple choice question has been scrambled)
  15. Which of the following factors is the MOST likely cause of a power supply fan failure?
    A. Extreme temperature variances
    B. Extreme humidity variances
    C. Power stability fluctuations
    D. Excessive dust accumulation
    D. Excessive dust accumulation
    (this multiple choice question has been scrambled)
  16. Which of the following ensures that air is passed through a server chassis correctly?
    A. Molex connectors
    B. Phase changers
    C. U-size templates
    D. Baffles
    D. Baffles
    (this multiple choice question has been scrambled)
  17. Which of the following technologies can detect and fix single bit memory errors?
    A. SDRAM
    B. ECC
    C. RAID
    D. Registered memory
    B. ECC
    (this multiple choice question has been scrambled)
  18. Which of the following storage tools could be used to initiate the rebuilding of a failed hard drive?
    A. Partitioning management
    B. Monitoring agents
    C. CHKDSK
    D. RAID array management
    D. RAID array management
    (this multiple choice question has been scrambled)
  19. Which of the following is a built-in feature of FAT?
    A. Encryption
    B. Compression
    C. Fault tolerance
    D. 8.3 name convention
    D. 8.3 name convention
    (this multiple choice question has been scrambled)
  20. An administrator needs to grant privileges to other server staff members to run archive utilities on a default Windows installation. The administrator needs to set the minimum permissions to:
    A. account operators.
    B. remote users.
    C. server operators.
    D. backup operators.
    D. backup operators.
    (this multiple choice question has been scrambled)
  21. Which of the following storage technologies connects by TCP/IP and is separate from the companys LAN?
    A. NAS
    B. Tape library
    C. SAN
    D. Optical jukebox
    C. SAN
    (this multiple choice question has been scrambled)
  22. Which of the following replication methods provides a disaster recovery system with minimal down time to normal operations?
    A. GFS
    B. Warm site
    C. Cold site
    D. Hot site
    D. Hot site
    (this multiple choice question has been scrambled)
  23. Which of the following server clusters offers increased availability, performance, and scalability?
    A. Active/passive
    B. Passive/passive
    C. Active/active
    D. Passive/active
    C. Active/active
    (this multiple choice question has been scrambled)
  24. Which of the following must occur when installing SCSI devices into the server?
    A. Set the jumper to cable select.
    B. Set the jumper to device ID 0.
    C. Terminate the back end of the chain.
    D. Terminate both ends of the chain.
    D. Terminate both ends of the chain.
    (this multiple choice question has been scrambled)
  25. An administrator recently installed a new array controller into a server. When the server is running POST the controller does not appear as present. Which of the following could be the reason for this?
    A. The server does not have the correct drivers.
    B. The server hard drives have not begun to spin.
    C. The server BIOS firmware is out-of-date.
    D. The server has too little memory installed.
    C. The server BIOS firmware is out-of-date.
    (this multiple choice question has been scrambled)
  26. A small push button typically found on the inside of a server case is MOST likely used for which of the following purposes?
    A. UID switch
    B. Cooling fan switch
    C. Power switch
    D. Chassis intrusion switch
    D. Chassis intrusion switch
    (this multiple choice question has been scrambled)
  27. Which of the following servers is responsible for translating an FQDN to an IP address?
    A. WINS
    B. DHCP
    C. DNS
    D. NTP
    C. DNS
    (this multiple choice question has been scrambled)
  28. Which of the following servers would execute SQL?
    A. NAS Server
    B. DNS Server
    C. Web Server
    D. Database Server
    D. Database Server
    (this multiple choice question has been scrambled)
  29. A new storage array must be configured for a database server. This array will store transaction logs that are always being written. Which of the following RAID solutions would provide fault tolerance and fast write operations without the use of parity?
    A. RAID 0
    B. RAID 3
    C. RAID 10
    D. RAID 6
    C. RAID 10
    (this multiple choice question has been scrambled)
  30. Which of the following storage protocols would be suitable for transport across an IP network?
    A. SAS
    B. SCSI
    C. iSCSI
    D. SATA
    C. iSCSI
    (this multiple choice question has been scrambled)
  31. Memory utilization by the print spooler process is constantly climbing after users begin to print to a certain type of printer. Which of the following is the MOST likely cause of the problem?
    A. The disk drive is out of free space
    B. Memory leak in the print spooler
    C. Corrupted print spooler software
    D. Memory leak in one of the print drivers
    D. Memory leak in one of the print drivers
    (this multiple choice question has been scrambled)
  32. Which of the following could be used to restrict access to the local web server to only certain IP addresses?
    A. Block port 80.
    B. Create an ACL.
    C. Create an application exception.
    D. Configure IPSec.
    B. Create an ACL.
    (this multiple choice question has been scrambled)
  33. Which of the following server virtualization features would BEST allow an administrator to quickly prepare a virtual server so that it is ready for use?
    A. Remote configuration
    B. Native RIS integration
    C. No physical hardware to setup
    D. Clone the machine from a template
    D. Clone the machine from a template
    (this multiple choice question has been scrambled)
  34. An application server is running slowly. After viewing performance monitoring data it is detected that the disk queue length is high. Which of the following could BEST resolve the situation?
    A. Add more memory to stop paging to disk.
    B. Add more disk drives.
    C. Increase the amount of virtual memory.
    D. Add a faster processor.
    A. Add more memory to stop paging to disk.
    (this multiple choice question has been scrambled)
  35. Multiple expansion cards are installed in a rack mount 1U server. All expansion cards stop working simultaneously. Which of the following is the MOST likely cause of the problem?
    A. Operating system
    B. Expansion cards
    C. Riser cards
    D. Motherboard
    C. Riser cards
    (this multiple choice question has been scrambled)
  36. While installing a new PCI card the administrator touched the motherboard. While powering on the server, a series of beeps were emitted and the server did not POST. Which of the following could be done to prevent this problem?
    A. Use a system board tester to check for compatibility issues.
    B. Use ESD equipment.
    C. Verify correct voltages are being supplied.
    D. Install compatible PCI cards.
    B. Use ESD equipment.
    (this multiple choice question has been scrambled)
  37. Which of the following describes the FINAL step in the troubleshooting process?
    A. Test the theory to determine the cause.
    B. Verify full system functionality.
    C. Root cause analysis.
    D. Implement the change.
    C. Root cause analysis.
    (this multiple choice question has been scrambled)
  38. Which of the following are enhancements from the FAT32 file system to the NTFS file system? (Select TWO).
    A. Ability to utilize redundant hardware devices
    B. Ability to create a larger partition size
    C. Ability to image new server deployments
    D. Ability to set file security permissions
    E. Ability to create virtual machines
    • B. Ability to create a larger partition size
    • D. Ability to set file security permissions
  39. Which of the following should an administrator utilize FIRST after installing a new HBA?
    A. Multiple RAID configurations
    B. Digitally signed device drivers
    C. Virtual machine components
    D. New Technology File Systems (NTFS)
    B. Digitally signed device drivers
    (this multiple choice question has been scrambled)
  40. Which of the following will MOST likely cause major performance issues on an email server?
    A. PBX software
    B. Anti-virus software
    C. DHCP server
    D. RAID 0 configuration
    B. Anti-virus software
    (this multiple choice question has been scrambled)
  41. Which of the following is the BEST way to ensure that all users receive a mapping to multiple shared drives?
    A. Logon scripts
    B. Local policy
    C. Set NTFS permissions
    D. Configure individual user accounts
    A. Logon scripts
    (this multiple choice question has been scrambled)
  42. Which of the following is a key component of a directory services server?
    A. RIS
    B. RAS
    C. VPN
    D. LDAP
    D. LDAP
    (this multiple choice question has been scrambled)
  43. Assuming the network supports all speeds, which of the following should an administrator use to get the MOST throughput?
    A. 10/100 full duplex NIC
    B. Gigabit NIC
    C. 100 half duplex NIC
    D. CAT5 cabling
    B. Gigabit NIC
    (this multiple choice question has been scrambled)
  44. Which of the following offers the MOST redundancy for a system but is also very costly?
    A. Disk-to-disk replication
    B. RAID implementation
    C. Hot site replication
    D. Server-to-server clustering
    C. Hot site replication
    (this multiple choice question has been scrambled)
  45. Which of the following is the MOST important consideration when implementing a data retention program?
    A. The companys individual data retention policies
    B. The data destruction requirements
    C. The laws and legal requirements of the data
    D. The user awareness training program
    C. The laws and legal requirements of the data
    (this multiple choice question has been scrambled)
  46. Which of the following is the MOST important step in any disaster recovery plan?
    A. Classifying systems according to operational impact
    B. Use appropriate fire suppressant systems
    C. The disaster recovery testing process
    D. Appropriate use of backup media and offsite storage
    C. The disaster recovery testing process
    (this multiple choice question has been scrambled)
  47. The server room that an administrator manages has just caught fire. Which of the following is the FIRST thing that the administrator should do?
    A. Evacuate all personnel.
    B. Notify staff of the potential service outage.
    C. Grab the backup tapes and exit the server room.
    D. Use fire suppression techniques until the fire department arrives.
    A. Evacuate all personnel.
    (this multiple choice question has been scrambled)
  48. Which of the following is the EASIEST way to centrally deploy software?
    A. Optical media
    B. USB
    C. PXE
    D. Network share
    D. Network share
    (this multiple choice question has been scrambled)
  49. After a server has been installed into a rack, an administrator must ensure which of the following?
    A. Determine the correct power requirements
    B. Verify the change control process can be implemented
    C. The system is labeled so that it can be identified
    D. Warm air flow is permitted through the front bezel
    C. The system is labeled so that it can be identified
    (this multiple choice question has been scrambled)
  50. Which of the following devices is used to provide appropriate voltage to the CPU?
    A. Heat sink
    B. HBAs
    C. Redundant power supply
    D. VRM
    D. VRM
    (this multiple choice question has been scrambled)
  51. An administrator is adding memory to a server. Once the system boots up, the same amount of memory appears as before the upgrade. Which of the following is the MOST likely cause?
    A. The memory is not installed in the correct slot.
    B. The memory is not the correct speed.
    C. The memory does not have the correct timing.
    D. The memory is not the correct CAS latency.
    A. The memory is not installed in the correct slot.
    (this multiple choice question has been scrambled)
  52. An administrator is installing Windows Server 2003 via CD on a new server with an SAS RAID array. When the administrator reaches the option to select the target installation drive, there are no drives listed. Which of the following is the FIRST thing the administrator should do?
    A. Shut down the server and check that all RAID drives are connected properly.
    B. Go into the BIOS and set all RAID drives to compatibility mode.
    C. Restart the installation via WDS.
    D. Restart the installation from CD and press F6 to install RAID drivers.
    D. Restart the installation from CD and press F6 to install RAID drivers.
    (this multiple choice question has been scrambled)
  53. Which of the following is a benefit of a hot spare?
    A. Enhanced performance
    B. Lower cost
    C. Allows two RAID 1 drives to simultaneously fail without losing any data
    D. Enhanced fault tolerance
    D. Enhanced fault tolerance
    (this multiple choice question has been scrambled)
  54. Which of the following backup methodologies is MOST time efficient for restoring data?
    A. Full
    B. GFS
    C. Incremental
    D. Differential
    A. Full
    (this multiple choice question has been scrambled)
  55. An administrator has just finished physically replacing the system board in a Windows domain controller. Which of the following must be done before booting the server back into Windows?
    A. Update the firmware on the SCSI controller.
    B. Update the firmware to the latest version.
    C. Configure IPMI on the new board.
    D. Update the time and date in the BIOS.
    D. Update the time and date in the BIOS.
    (this multiple choice question has been scrambled)
  56. An administrator has shut down a server to install additional memory. When the administrator restarts the server after the upgrade, it times out. Which of the following could be the cause of the problem? (Select TWO).
    A. Processor failure
    B. Third party memory
    C. Disk drive failure
    D. ESD during the upgrade
    E. Backplane failure
    • B. Third party memory
    • D. ESD during the upgrade
  57. Which of the following ensures the MOST secure access to a server room?
    A. Server rack doors
    B. Biometric devices
    C. ID card readers
    D. Locked doors
    B. Biometric devices
    (this multiple choice question has been scrambled)
  58. Which of the following is the BEST sequence to bare metal restore a server?
    A. Restore applications, restore data, and verify data.
    B. Restore OS, restore system applications, and restore data.
    C. Contact end users of outage, restore backup data, and verify data.
    D. Determine backups available, restore backups, and verify data.
    B. Restore OS, restore system applications, and restore data.
    (this multiple choice question has been scrambled)
  59. Which of the following allows an administrator to recover the MOST data?
    A. Incremental backup
    B. System state restore
    C. Differential backup
    D. System image
    D. System image
    (this multiple choice question has been scrambled)
  60. A server was recently updated with the latest antivirus definitions. Immediately after the update, the server begins to report file not found errors for a mission critical application. Which of the following is the MOST likely reason for this?
    A. The update was done incorrectly and now the server needs to be restarted.
    B. The update requires a reboot for the files to process correctly.
    C. The update has quarantined files that are false positives.
    D. The update has discovered viruses on the server and removed those virus files.
    C. The update has quarantined files that are false positives.
    (this multiple choice question has been scrambled)
  61. An administrator needs to update the anti-virus, security patches, BIOS, and the web server software on a production system. Which of the following is the BEST method to accomplish this?
    A. Update the web software, security patches, anti-virus, and then the BIOS.
    B. Update anti-virus, security patches, BIOS software, and then the web software.
    C. Update security patches, BIOS, web software, and then the anti-virus.
    D. The order does not matter, only one change at a time should be done.
    D. The order does not matter, only one change at a time should be done.
    (this multiple choice question has been scrambled)
  62. An administrator has just installed a web server for the companys Internet site. After bringing the system online, customers notify the administrator that they cannot connect to the server. The administrator tests the web server from a workstation and can access the website. The customers continue to report issues. Which of the following is the MOST likely reason for this?
    A. The company firewall is misconfigured.
    B. The server's timeout feature is set incorrectly.
    C. The servers firewall is misconfigured.
    D. The web server was not installed properly.
    A. The company firewall is misconfigured.
    (this multiple choice question has been scrambled)
  63. An email server has been installed; however, the staff reports that they are unable to receive email from external email addresses, but they can email each other. Which of the following is the MOST likely reason for this?
    A. The DNS server is only resolving internal name spaces.
    B. The DHCP server is misconfigured.
    C. The company firewall is blocking SMTP ports.
    D. The email server should be configured to resolve names by IP addresses.
    C. The company firewall is blocking SMTP ports.
    (this multiple choice question has been scrambled)
  64. An administrator needs to add fault tolerance capabilities to a server. Which of the following is the BEST solution to accomplish this?
    A. Install a fail-over cable.
    B. Move the architecture from 32-bit to 64-bit.
    C. Install a PBX card.
    D. Install a second NIC card.
    D. Install a second NIC card.
    (this multiple choice question has been scrambled)
  65. Which of the following components provides for the BEST hardware cooling features?
    A. Epoxy paste
    B. Virtualization
    C. Heat sink
    D. Chip fan
    D. Chip fan
    (this multiple choice question has been scrambled)
  66. An administrator is running proprietary server software that requires services to be reconfigured every time the server is upgraded to the latest vendor version. Which of the following is the BEST solution to address this problem?
    A. The current system configuration should be documented for future use.
    B. A copy of the latest pre-installation plan should be developed and utilized.
    C. Vendor support should be contacted so that they can correct the issue.
    D. Server diagramming and environmental topologies should be documented.
    A. The current system configuration should be documented for future use.
    (this multiple choice question has been scrambled)
  67. A data center has had a power outage. Which of the following should the administrator do FIRST once the power is restored?
    A. Identify which systems are the most critical and bring them up by level of importance.
    B. Retrieve the latest backup tapes for immediate system restore using the GFS rotation.
    C. Determine the cause of the power outage and install UPS systems to prevent its reoccurrence.
    D. Identify the least critical systems and then power those systems on first.
    A. Identify which systems are the most critical and bring them up by level of importance.
    (this multiple choice question has been scrambled)
  68. An administrator is planning to bring a newly purchased server online. Which of the following should the administrator do FIRST?
    A. Follow the pre-installation plan and procedures.
    B. Review the system logs to check for errors.
    C. Notify all users that the old system will be taken offline.
    D. Apply all security updates to the system.
    A. Follow the pre-installation plan and procedures.
    (this multiple choice question has been scrambled)
  69. A system administrator needs to maintain 1.2TB of storage for a database server. There are six 250GB drives available in the server for storage space. Which of the following RAID configurations would be the BEST choice given that performance and fault tolerance are important factors?
    A. RAID 0 across all 6 drives
    B. RAID 1 across drive pairs totaling 3 pairs
    C. RAID 5 across all 6 drives
    D. RAID 10 across all 6 drives
    C. RAID 5 across all 6 drives
    (this multiple choice question has been scrambled)
  70. An administrator needs to maintain 1TB of storage space for a server. A performance critical application will use this storage space for a database. The database will be replicated between multiple servers. Cost and performance are the most important considerations. Which of the following RAID configurations would be the BEST choice for the storage array?
    A. RAID 10 with eight 250GB hard drives
    B. RAID 6 with six 250GB hard drives
    C. RAID 5 with five 250GB hard drives
    D. RAID 0 with four 250GB hard drives
    D. RAID 0 with four 250GB hard drives
    (this multiple choice question has been scrambled)
  71. A new server has ten 250GB drives ordered with it. An administrator needs to create two arrays, one for the operating system and the other for the storage array. The operating system array needs to be able to hold 25GB of data, fault tolerant, and have the least amount of unused drive space. The storage array must be able to hold at least 600GB of data, be fault tolerant, and have decent performance. The storage array should contain room for the data to double over the upcoming year. There will be available spare parts on hand to support this server in the event of a failure. Which of the following RAID configurations would BEST suit the needs for this server?
    A. OS: RAID 1 with two 250GB hard drives
    Storage: RAID 5 with eight 250GB drives
    B. OS: RAID 1 with two 250GB hard drives
    Storage: RAID 10 with four 250GB hard drives
    C. OS: RAID 5 with three 250GB hard drives
    Storage: RAID 5 with seven 250GB hard drives
    D. OS: no RAID with one 250GB hard drive
    Storage: RAID 6 with nine 250GB hard drivesb
    • A. OS: RAID 1 with two 250GB hard drives
    • Storage: RAID 5 with eight 250GB drives
  72. RAID 5 can be BEST described as which of the following?
    A. Mirroring with striping
    B. Independent disks with shared parity
    C. Striping with dedicated parity
    D. Striping with distributed parity
    D. Striping with distributed parity
    (this multiple choice question has been scrambled)
  73. Which of the following is a benefit of RAID 1?
    A. Higher capacity
    B. Higher performance
    C. Fault tolerance
    D. Multiple failure fault tolerance
    C. Fault tolerance
    (this multiple choice question has been scrambled)
  74. Which of the following is a disadvantage of RAID 10?
    A. Higher cost
    B. No fault tolerance
    C. Not supported by many RAID controllers
    D. Poor performance
    A. Higher cost
    (this multiple choice question has been scrambled)
  75. A tape library can be defined as which of the following?
    A. A way to catalog tapes after a tape backup to easily identify and retrieve data.
    B. A database consisting of all backups performed and the contents of each backup.
    C. An offsite storage facility to house tapes in case of a disaster for easy site recovery.
    D. A modular tape backup system containing multiple drives, tapes, and connections.
    D. A modular tape backup system containing multiple drives, tapes, and connections.
    (this multiple choice question has been scrambled)
  76. Which of the following storage interface protocols has the FASTEST speeds?
    A. SAS
    B. Ultra2 SCSI
    C. Ultra320 SCSI
    D. SATA
    A. SAS
    (this multiple choice question has been scrambled)
  77. A WORM drive can be equated to which of the following common technologies?
    A. DVDRW
    B. CDR
    C. Flash Media
    D. CDRW
    B. CDR
    (this multiple choice question has been scrambled)
  78. According to best practices, which of the following should be the FIRST step after a full boot into a newly installed Windows Server OS?
    A. Remove the Internet Explorer Enhanced Security configuration.
    B. Disable the Guest account.
    C. Apportion additional storage.
    D. Apply all relevant updates and patches.
    D. Apply all relevant updates and patches.
    (this multiple choice question has been scrambled)
  79. Which of the following are benefits to server virtualization? (Select THREE).
    A. Better server hardware leverage
    B. Increased application security
    C. Smaller backup window needed
    D. Lower power consumption
    E. Smaller datacenter footprint
    F. Little to no maintenance needed
    • A. Better server hardware leverage
    • D. Lower power consumption
    • E. Smaller datacenter footprint
  80. Which of the following software directly interacts with the hardware and handles hardware resource requests from virtual machines?
    A. Virtual Center
    B. Hypervisor
    C. Guest OS
    D. VT
    B. Hypervisor
    (this multiple choice question has been scrambled)
Author
ID
85062
Card Set
iatii-b
Description
series b
Updated
Show Answers